Eaton i-on40H - Page 149

Log Messages
Page 139
Alarm Conf. ==
Confirmed alarm with tamper on
expander.
Alarm Conf. VKP
Confirmed alarm with tamper on
virtual keypad.
Alarm Confirm RK==
Confirmed alarm with tamper on
radio keypad.
Alarm Confirm Z==
Confirmed alarm on zone.
Alarm Confirm
Confirmed alarm.
Alarm Test Call
Periodic alarm test call made.
Alarm Test Call
Manual alarm test call made.
All Comms Pths Flt
All communications paths have a
fault.
All Comms Pths Rst
All communications path faults
restored.
Alm Conf Bus# Tamp
An alarm was confirmed by a bus
tamper.
Alm Conf Panel Jam
Alarm confirmed by panel
jamming.
Alm Conf Panel Lid
Confirmed alarm with tamper on
control unit lid.
Alm Confirm SRN==
Confirmed alarm with tamper on
radio siren n.
Alm Confirm WAM==
Confirmed alarm with tamper on
WAM n.
AS defer U-- P#
User nn defered calendar setting
on partition n.
ATE L.F. All
All lines to alarm transmission
equipment failed.
ATE L.F. Restore
Line to alarm transmission
equipment restored.
ATE L.F. Single
Alarm transmission equipment has
a single line fault.
Auto Part Set #
The system was part set by
calendar setting.
Auto Ptn # PtSet
Partition n was part set by
calendar setting.
Auto Ptn # Set
Partition n set by calendar setting.
Auto Ptn # Unset
Partition n unset by calendar
setting.
Auto System Set
The system was full set by
calendar setting.
Auto System Unset
The system was unset by calendar
setting.
Autoset defer U--
User defered calendar setting of
system.
Autoset Fail P#
Calendar setting of partition failed.
Autoset Fail
Calendar setting of system failed.
Aux # Tamper Rstr
Aux Tamper terminals on main
pcb closed circuit
Aux # Tamper
Aux Tamper terminals on main
pcb open circuit
Aux. 14V4 # Fail
Control unit 14.4V supply failed.
Aux. 14V4 # Rstr
Control unit 14.4V supply restored.
Auxiliary 12V Fail
Control unit 12V Aux DC not
working.
Auxiliary 12V Rstr
Control unit 12V Aux DC restored.
Bad checksum
There is an error on loading the
control unit with its software.
Batt = Fault Rst
Control unit battery restored.
Batt = Load Fail
Control unit battery failed load test.
Batt = Low/Missing
Control unit battery missing or low.
Batt= Charger Fail
Control unit battery charger failed.
Batt= Charger Rstr
Control unit battery charger
working again.
Battery Load OK
Control unit battery passed load
test.
Bell # 12V Fail
12V DC supply to bell failed.
Bell # 12V Restore
12V DC supply to bell restored.
Bell # Tamper Rstr
External wired siren tamper
restored.
Bell # Tamper
External wired siren tamper.
Burg Z== Alarm
Burglar alarm on zone n.
Burg Z== Restore
Burglar alarm on zone n restored.
Bus # 12V Fail
12V DC supply to Bus nn failed.
Bus # 12V Restore
12V DC supply to Bus nn restored.
Bus # Tamper Rstr
Bus n has been restored.
Bus # Tamper
Bus n has been tampered (for
example wires cut or
disconnected)
Codes Defaulted
All access codes were returned to
factory defaults.
Comms 12V Fail
DC power to comms module
failed.
Comms 12V Restore
DC power to comms module
restored.
Configuration Fail
The current configuration is not
compatible with the software
revision level of the control unit.
Defaults Loaded
The control unit was returned to
factory defaults.
Disabled ==
Expander/Keypad disabled.
Downloader Lockout
Downloader locked out for 30 mins
due to 10 consecutive
authentication errors.
Dup. == Restore
Duplicate bus device nn restored.
Duplicate ==
Duplicate bus device nn detected.
Email error ---
See "Email error messages" on
page 142.
Email Test Call
Email test call initiated by Installer.
Enabled ==
Expander/Keypad enabled.
Entry Started Z==
Entry started by zone n.
Entry Stray Z==
Stray on entry alarm at zone n.
Exit Mode Changed
Local setting mode applied (from
Remote set).
Exp. == deleted
Expander n deleted from bus.
Expndr == added
Expander n added to bus.
Expndr == found
New expander n found on bus.
Ext A/C Fail Z==
Zone n with type AC Fail activated.
Ext A/C Rstr Z==
Zone n with type AC Fail restored.
Ext Batt Fault Z==
Zone n with type Batt Fault
activated.
Ext Batt Rstr Z==
Zone n with type Batt Fault
restored.
Ext Low Volts Z==
Zone n with type Low Volts
activated.
Ext PSU Fault Z==
Zone n with type Fault activated.
Ext PSU Rstr Z==
Zone n with type Fault restored.
Ext Volts Rstr Z==
Zone n with type Low Volts
restored.
Ext WD Fault Z===
A warning device has reported a
fault through zone n.
Ext WD Restr Z===
The fault reported through zone nn
by a warning device has been
restored.
Fire == Alarm
Fire alarm at keypad.
Fire Reset
User reset system after fire alarm.
Fire Restore
Fire alarm at keypad restored.
Fire Restore
Fire alarm restored from radio
keypad.
Fire Z== Alarm
Fire alarm on zone n.
Fire Z== Restore
Fire alarm on zone n restored.
GSM CME Info --
The GSM plu-on module has a
problem.
GSM CMS Info --
The GSM plu-on module has a
problem.
HUA Cnf RF HD U---
Hold Up Alarm confirmed by radio
HUD belonging to user nn.
HUA Cnf RF MD U---
Hold Up Alarm confirmed by radio
Man Down transmitter belonging
to user nn.
HUA Conf ==RKBS
Hold Up Alarm confirmed by a
tamper on RKBS n.
HUA Conf Bus# Tamp
Hold Up Alarm by a bus tamper.
HUA Conf HD ==
Hold Up Alarm confirmed on
keypad HUA keys.
HUA Conf HD RK==
Hold Up Alarm confirmed on radio
keypad HUA keys.
HUA Conf Panel Jam
Hold up alarm confirmed by panel
jamming.
HUA Conf Panel Lid
Hold Up Alarm confirmed by panel
lid tamper.