ebm-papst S3G800-BT21-01 - User Manual

Operating instructions
S3G800-BT21-01
Translation of the original operating instructions
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 7938 81-0
Fax +49 (0) 7938 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
CONTENTS
1. SAFETY REGULATIONS AND INFORMATION
11. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1.1 Hazard levels for warnings
11.1 Hazard levels for warnings
These operating instructions use the following hazard levels to indicate
potentially hazardous situations and important safety regulations:
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
1.2 Staff qualifications
11.2 Staff qualifications
The device may only be transported, unpacked, installed, operated,
maintained and otherwise used by suitably qualified, trained and
authorized technical staff.
Only authorized specialists are permitted to install the device, to carry
out a test run and to perform work on the electrical installation.
1.3 Basic safety rules
11.3 Basic safety rules
The safety hazards associated with the device must be assessed again
following installation in the final product.
The locally applicable industrial safety regulations are always to be
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
11.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 6.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
21.5 Safety and protective features
21.6 Electromagnetic radiation
21.7 Mechanical movement
21.8 Emissions
21.9 Hot surface
21.10 Transport
31.11 Storage
32. INTENDED USE
43. TECHNICAL DATA
43.1 Product drawing
53.2 Nominal data
53.3 Data according to Commission Regulation (EU) 327/2011
53.4 Technical description
63.5 Mounting data
63.6 Transport and storage conditions
63.7 Electromagnetic compatibility
64. CONNECTION AND STARTUP
64.1 Mechanical connection
64.2 Electrical connection
84.3 Connection in terminal box
94.4 Factory settings
104.5 Connection diagram
124.6 Checking connections
124.7 Switching on the device
124.8 Switching off the device
125. INTEGRATED PROTECTIVE FEATURES
126. MAINTENANCE, MALFUNCTIONS, POSSIBLE
CAUSES AND REMEDIES
136.1 Cleaning
146.2 Safety inspection
146.3 Disposal
Item no. 50138-5-9970 · ENU · Change 209539 · Approved 2021-02-09 · Page 1 / 14
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary

Safety Regulations and Information

Hazard Levels for Warnings

Explains hazard symbols (DANGER, WARNING, CAUTION, NOTE) and their meanings for safety.

Staff Qualifications

Specifies required qualifications for personnel handling the device.

Basic Safety Rules

Outlines general safety practices and workplace tidiness for safe operation.

Voltage Safety

Addresses electrical safety, checking intervals, and cable integrity.

Safety and Protective Features

Details safety measures like guards, protective devices, and entanglement prevention.

Electromagnetic Radiation

Discusses potential interference from electromagnetic radiation and shielding measures.

Mechanical Movement Hazards

Covers hazards related to rotating parts, entanglement, and ejected parts.

Emissions and Noise Levels

Warns about potential noise levels and required protective measures.

Hot Surface Warning

Advises caution regarding hot motor housing and the risk of burns.

Transport Instructions

Provides guidelines for safe transportation of the fan.

Storage Guidelines

Gives instructions for storing the device properly to maintain its condition.

Intended Use and Improper Operation

Prohibited Operations

Lists prohibited and hazardous operating conditions, defining improper use.

Technical Data and Specifications

Product Drawing and Dimensions

Presents a dimensional drawing of the product with key labels and measurements.

Nominal Data

Lists technical specifications like voltage, current, speed, and temperature ranges.

EU Energy Efficiency Data

Provides energy efficiency data as per Commission Regulation (EU) 327/2011.

Technical Description

Details product specifications like weight, materials, and key features.

Mounting Data

Specifies requirements for screw strength and fastening during installation.

Transport and Storage Conditions

Lists permitted ambient temperature ranges for transport and storage.

Electromagnetic Compatibility

States EMC standards for interference immunity and emission.

Connection and Startup Procedures

Mechanical Connection

Instructions for physically connecting the fan, including handling precautions.

Electrical Connection Requirements

Guidelines for safe electrical hookup, including grounding and cable types.

Supply Connection and Fuses

Details fuse assignments and cable cross-sections for supply connection.

Terminal Box Connection

Details on connecting wires within the terminal box and cable routing.

Factory Settings

Lists default configuration settings for the device, such as PWM control.

Connection Diagram

Illustrates the electrical connections for the fan and its terminals.

Checking Connections

Procedures for verifying all connections are secure and correct before operation.

Switching On the Device

Steps and precautions for powering up the fan for the first time.

Switching Off the Device

Methods for safely powering down the fan during operation or maintenance.

Integrated Protective Features

Maintenance, Malfunctions, and Remedies

Impeller Running Smoothly

Troubleshooting steps for impeller imbalance or smooth running issues.

Motor Not Turning

Diagnosing and resolving issues when the motor fails to start.

Deficient Cooling

Steps to take if the device experiences deficient cooling.

High Ambient Temperature

Actions to take when the ambient temperature exceeds operational limits.

Cleaning Procedures

Procedures and safety precautions for cleaning the fan to ensure service life.

Safety Inspection and Disposal

Regular Safety Inspections

Details regular checks for safety compliance and component integrity.

Product Disposal Recommendations

Recommendations for environmentally sound disposal of the product and components.

Country-Specific Legal Requirements

Emphasizes adherence to applicable local legal regulations for product disposal.

Disassembly Instructions

Instructions for safe disassembly by qualified personnel.

Component Disposal and Recycling

Guidelines for separating and recycling product components.

ebm-papst S3G800-BT21-01 Specifications

General

Brand	ebm-papst
Model	S3G800-BT21-01
Category	Fan
Language	English