- 35 -
ENGLISH
INSTRUCTIONS FOR USE
:HHNO\WLPHU
3ress and hold the “M” key on the remote control for 2 seconds. 7his turns on the clock regulation and by pressing the µ¶
key, the weekly timer function is accessed, with the display showing the description “3RO*RAMM ONOFF”.
7his function allows you to select the type of programming, which allows a ma[imum of three ignitions to be set.
As you con¿rm the display with the key “M”, one of the following options will appear:
NO 3RO*. (no programme set)
DAILY 3RO*RAM (single programme for every day of the week)
WEEKLY 3RO*RAM. (speci¿c programme for each day individually)
Use the “” and “±” keys to switch between programmes.
&on¿rming by pressing the “M” key “DAILY 3RO*RAM.” and pressing the “” key, the choice of the number of programmes
(ignitione[tinguishing) per day can be made.
Use the “DAILY 3RO*RAM” to set identical programmes for every day of the week.
By then pressing the “” key, the following can be seen:
- 3rog. no.
- 1st prog. (one turn on and one turn off per day), 2nd prog. (identical), rd prog. (identical)
Use the “±” key to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
7he display shows: 1 “ON” at 10 Use the “” and “±” key to change the hour. &on¿rm with the “M” key (All 1 On+our 10).
7he display shows: 1 “ON” at 0 Use the “” and “±” key to change the minutes. &on¿rm with the “M” key (1 Off min).
7
he same applies for the turn-off time to be set and for subsequent turning on and off.
&on¿rm by pressing “M” and the wording “SA9E""” will appear on the display.y.
When con¿rming ”WEEKLY 3RO*RAM”, you will need to choose the day to which the programming is to apply:
7 Sat; 3rogr.1; 1 Mon ; 2 7ues; Wed; 4 7hurs; 5 Fri; 6 Sa;
Once the day is set, use the keys “” and “” and con¿rm by pushing “M” key to choose 1 to ignitions, to programme in the
same way as for the “DAILY 3RO*RAM”, choosing whether or not to enable a programme for each day of the week, and if so
choosing number of interventions and at what times.
Should you make an error during programming, you can leave the programme without saving. As you press a key,
, he di-
splay will show the word “no SA9E”.
&KDQJLQJSHOOHWORDGLQJ(with self-regulation deactivated)
When the “M” key on the radio control is held down for two seconds and the display is scrolled using the “” and “±” keys,
you come across the “User¶s Menu”. When this is con¿rmed the display reads “AD--3ELLE7 ; AD--DRAU*+7 and RADIO
MENU” (&A7). 7he pellet drop can be adjusted manually by changing the capacity in percentage terms (- 0 %).
By con¿rming this function with the menu key, you can access the function to adjust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value set, pellet loading increases. 7his function is useful if
changing the pellet type for which the stove has been calibrated and loading therefore needs correcting.
Should this correction not suf¿ce, contact the Edilkamin-authorised Dealer, to establish the new operating a[is.
1RWHVRQÀDPHYDULDELOLW\
Flame status may vary depending on the type of pellet used, in addition to normal solid fuel Àame variability and regular combu-
stion chamber cleaning carried out automatically by the boiler.
(N.B.: which does NO7 replace necessary cold suction by the user prior to ignition).
5(6(59(:$51,1*
7he stove is ¿tted with an electronic function that detects the residual quantity of pellets in the tank.
7he detection system is integrated into the electronic board, allowing you to see how many hours and kg are left until
pellet e[haustion, at all times. For correct system function, it is important that the following procedure is followed during the ¿rst
ignition (by the Dealer).
7his provides a reference indicator. *reater precision is obtained by regularly zeroing the system before ¿lling it again. Edilkamin
does not accept any responsibility for differences from what is indicated (which may be due to e[ternal factors).
To Next Page
Loading...
Need help?
General
