v
• FIGURE 5-9 TERMINAL BLOCK DIAGRAM ...................................................................................................5-7
• FIGURE 5-10 TB1 TERMINAL DETAILS........................................................................................................5-7
• FIGURE 5-11 THE FINGER GUARD IN PLACE................................................................................................5-9
• FIGURE 5-12 THE TERMINAL COVER TAMPER DETECT BUTTON ............................................................. 5-10
• FIGURE 5-13 LOCATION OF THE CONFIG “JUMPER”................................................................................ 5-11
• FIGURE 5-14 TB1 CONNECTIONS ............................................................................................................ 5-11
• FIGURE 5-15 INTERNAL CONNECTION OPTIONS....................................................................................... 5-12
• FIGURE 5-16 LCD WITH ALL SEGMENTS TURNED ON ............................................................................. 5-16
• FIGURE 5-17 LOCATION OF THE BILLING RESET / BOOST BUTTON .......................................................... 5-17
• FIGURE 5-18 METER WITH AN EXTENDED TERMINAL COVER FITTED ................................................... 5-18
• FIGURE 5-19 AN ETM9300 MODEM FITTED TO THE METER ................................................................... 5-18
• FIGURE 5-20 A SAM2 MODEM FITTED UNDER THE TERMINAL COVER .................................................. 5-19
• FIGURE 5-21 ANTENNA FITTED UNDER THE TERMINAL COVER .............................................................. 5-19
• FIGURE 6-1 OVERALL DIMENSIONS OF THE METER ....................................................................................6-1
• FIGURE 6-2 MOUNTING POINTS ..................................................................................................................6-2
• FIGURE 6-3 FRONT VIEW OF THE METER WITH TERMINAL COVER FITTED.................................................6-3
• FIGURE 6-4 UNDER THE TERMINAL COVER OF THE METER ........................................................................6-4
• FIGURE 6-5 TERMINAL BLOCK DIAGRAM ...................................................................................................6-5
• FIGURE 6-6 TB1 TERMINAL SPACING .........................................................................................................6-6
• FIGURE 6-7 THE TERMINAL COVER TAMPER DETECT BUTTON ..................................................................6-6
• FIGURE 6-8 LOCATION OF THE CT TO VT LINKS........................................................................................6-7
• FIGURE 6-9 METER WITH THE CT TO VT LINKS DISCONNECTED BY SLIDING SHIMS................................6-7
• FIGURE 6-10 METER WITH THE CT TO VT LINKS DISCONNECTED BY REMOVING SCREWS......................6-7
• FIGURE 6-11 LOCATION OF THE CT TO VT LINKS......................................................................................6-8
• FIGURE 6-12 METER WITH THE CT TO VT LINKS DISCONNECTED BY REMOVING SCREWS......................6-8
• FIGURE 6-13 LOCATION OF THE CONFIG JUMPER.......................................................................................6-8
• FIGURE 6-14 TB1 CT AND VT CONNECTIONS FOR 3 ELEMENT (TOP) AND 2 ELEMENT (BOTTOM). .........6-9
• FIGURE 6-15 CONNECTIONS FOR 3 ELEMENT WHOLE CURRENT ............................................................. 6-10
• FIGURE 6-16 TB1 CT AND VT CONNECTIONS FOR 3 ELEMENT TESTING ............................................... 6-10
• FIGURE 6-17 LCD WITH ALL SEGMENTS TURNED ON ............................................................................. 6-15
• FIGURE 7-1 LCD WITH ALL SEGMENTS TURNED ON ..................................................................................7-1
• FIGURE 7-2 CHINESE LCD WITH ALL SEGMENTS TURNED ON...................................................................7-2
• FIGURE 7-3 MK10D LCD WITH ALL SEGMENTS TURNED ON ....................................................................7-2
• FIGURE 7-4 MK10A LCD WITH ALL SEGMENTS TURNED ON ....................................................................7-2
• FIGURE 7-5 MK7 LCD WITH ALL SEGMENTS TURNED ON .........................................................................7-3
• FIGURE 7-6 EXAMPLE OF FIRST PAGE OF SET A LCD DISPLAY .................................................................7-4
• FIGURE A-1 ENERGY DIRECTIONS.............................................................................................................A-3
• FIGURE A-2 NAMING CONVENTION SETTINGS ............................................................................................A-4
vi EDMI Atlas Hardware Reference Manual
To Next Page
Loading...
Need help?
General
