Home
Edwards
Water Pump
XDS 10
Edwards XDS 10 User Manual
4
of 1
of 1 rating
42 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
© Edwards Limited 20
10. All
rights reserved.
Page 3
Edwards and Edwards lo
go are trademarks of Edwards Limited.
Introduction
A726-01-88
0 Issue M
Figure 1 - The single-phase XDS dry pump
1.
NW25 inlet port
2.
Gas-ballast control (not fitted on 05 variant)
3.
Cooling fan
4.
DN25NW/3/4
inch BSP exhaust
5.
Baseplate
6.
V
oltage indicator
7.
On/Off switch
8.
Hour counter
8
10
Table of Contents
Default Chapter
2
Declaration of Conformity
2
Table of Contents
3
Introduction
7
Scope and Definitions
7
ATEX Directive Implications
8
The Single-Phase XDS Dry Pump
9
Description
10
Gas-Ballast Control
10
Construction
10
CSA Product Classification
11
Technical Data
13
Operating and Storage Conditions
13
Performance
13
General
13
Performance Characteristics
14
Dimensions
15
Mechanical Data
16
General
16
Noise and Vibration Data
16
Electrical Data
16
Single-Phase Pumps
16
Three-Phase Pumps
16
Legislation and Standards
17
Installation
19
Safety
19
System Design Considerations
19
Unpack and Inspect
19
Lifting the Pump
20
Locate the Pump
20
Electrical Installation: Single-Phase Pumps
20
Check and Configure the Motor
20
Electrical Interface: Single-Phase Pumps
20
Connect the Pump to Your Electrical Supply
21
Check the Direction of Rotation
21
Underside of the Pump
22
Three-Phase Electrical Connections: 200-230 V
22
Three-Phase Electrical Connections: 380-460 V
22
Electrical Installation: Three-Phase Pumps
23
Check and Configure the Motor
23
Connect the Pump to Your Electrical Supply
23
Check the Direction of Rotation
24
Inlet and Outlet Connections
24
Leak Test the System
25
Operation
27
Gas-Ballast Control (if Fitted)
27
Start up Procedure
27
To Achieve Ultimate Vacuum (if Gas Ballast Fitted)
28
Pumps Already in Service
28
New Pumps, Pumps that Have Just Been Serviced or Reconditioned, and Pumps that Have Been in Storage
28
To Pump Condensable Vapours (if Gas Ballast Fitted)
28
Implication of ATEX Directive
28
Introduction
28
Flammable/Pyrophoric Materials
28
Gas Purges
29
Shut down
29
Maintenance
31
Safety Information
31
Maintenance Plan
31
Inspect and Clean the Inlet Strainer
32
Inspect and Clean the Gas-Ballast Control (if Fitted)
32
Inlet Strainer Assembly
32
Clean the External Fan Cover
33
Replace the Tip Seals and Exhaust Valve
33
Test the Motor Condition
33
Gas-Ballast Control Assembly
33
Fault-Finding
34
The Pump Has Failed to Start
34
The Pump Has Failed to Achieve the Required Performance
34
The Pump Is Noisy
34
The Pump Surface Temperature Is above 100 °C
34
The Pumping Speed Is Poor
34
Storage and Disposal
37
Storage
37
Disposal
37
Spares and Accessories
39
Introduction
39
Spares
39
Accessories
39
Solenoid Operated Pipeline Valve
39
Gas-Ballast Adaptor (Does Not Apply to 05 Variants)
39
Vibration Isolators
40
Exhaust Nozzle Kit
40
XDS Silencer
40
Index
41
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Edwards XDS 10 and is the answer not in the manual?
Ask a question
Edwards XDS 10 Specifications
General
Brand
Edwards
Model
XDS 10
Category
Water Pump
Language
English
Related product manuals
Edwards XDS Series
36 pages
Edwards XDS46i
40 pages
Edwards STP-XA3203BV155
169 pages
Edwards STP-XF803 Series
169 pages
Edwards STP-XA4503 Series
63 pages
Edwards STP-XA2703 Series
63 pages
iXM1200 Xcede customer special A
104 pages
Edwards E2M28
56 pages
Edwards iXM Series
104 pages
Edwards nEXT200200
100 pages
Edwards STP-iXA3306C
181 pages
Edwards STP-301 Series
121 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
