EINHELL TC-SM 216 - Technical Data for TC-SM 216; Technical Data for TC-SM 254; Noise Emission Levels

GB
- 27 -
4. Technical data
4.1 TC-SM 216
AC motor: ................................220-240 V ~ 50Hz
Power: ....................1500 W S1 / 1600 W S6 25%
Idle speed n
0
: ......................................5200 min
-1
Carbide saw blade: ...........ø 216 x ø 30 x 2.4 mm
Maximum tooth pitch ............................... 2.8 mm
Number of teeth: ............................................ 48
Swiveling range: .......................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Saw width at 90°: ............................305 x 65 mm
Saw width at 45°: ............................215 x 65 mm
Saw width at 2 x 45°
(double miter cut, left): ....................215 x 35 mm
Weight: .......................................... approx. 13 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class: ........................................... II/
쓑
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 160 mm.
Operating mode S6 25%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 25% of the cycle at the
specifi ed rating and must then be allowed to idle
for 75% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
L
pA
sound pressure level ..................... 95.5 dB(A)
K
pA
uncertainty ....................................... 3 dB (A)
L
WA
sound power level ..................... 108.5 dB(A)
K
WA
uncertainty ....................................... 3 dB (A)
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
4.2 TC-SM 254
AC motor: ................................220-240 V ~ 50Hz
Power: ....................1800 W S1 / 1900 W S6 25%
Idle speed n
0
: ......................................5000 min
-1
Carbide saw blade: ...........ø 254 x ø 30 x 2.4 mm
Maximum tooth pitch ............................... 2.8 mm
Number of teeth: ............................................ 48
Swiveling range: .......................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Saw width at 90°: ............................305 x 85 mm
Saw width at 45°: ............................215 x 85 mm
Saw width at 2 x 45°
(double miter cut, left): ....................215 x 45 mm
Weight: .......................................... approx. 15 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class: ........................................... II/
쓑
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 180 mm.
Operating mode S6 25%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 25% of the cycle at the
specifi ed rating and must then be allowed to idle
for 75% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
L
pA
sound pressure level .................... 96.7 dB (A)
K
pA
uncertainty ....................................... 3 dB (A)
L
WA
sound power level .................... 109.7 dB (A)
K
WA
uncertainty ....................................... 3 dB (A)
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TC_SM_216_SPK9.indb 27Anl_TC_SM_216_SPK9.indb 27 24.04.2019 09:30:4724.04.2019 09:30:47