EINHELL TC-SM 2531/2 U User Manual

GBGB
- 47 -
•
To set up the equipment again, proceed as
described in section 5.2.
6.9 Operating the laser (Fig. 2)
Switching on: Move the On/O switch (37) to the
“I” position to switch on the laser (35). A laser line
is projected onto the material you wish to process,
providing an exact guide for the cut.
Switching o: Move the On/O switch (37) to the
“0” position.
Setting the laser: If necessary, slacken the
screws to adjust the laser. Retighten the screws
after you have made the adjustment. Important!
Never look directly into the laser beam!
Replacing the battery: Ensure that the laser (35)
is switched o. Remove the battery compartment
cover (40). Remove the old batteries and replace
with new ones (2 x 1.5 Volt R03, LR 03 Micro,
AAA). Ensure correct polarity when inserting the
new batteries. Close the battery compartment
again.
6.10 Battery disposal
Recycle the packaging in an environmentally re-
sponsible manner. Sort the packaging for proper
recycling. The product may not be disposed of
with normal household refuse. Consumers have a
legal obligation to dispose of the batteries at the
appropriate collection points.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the authorized after-sales
service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
The ingress of water into an electric tool in-
creases the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by the autorized after sales
service agent.
Important! The carbon brushes should not be re-
placed by the autorized after sales service agent.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
Tip! For good results we
recommend high-quality ac-
cessories from !
www.kwb.eu
welcome@kwb.eu
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council oces.
10. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
Anl_TC_SM_2531_2_U_SPK8.indb 47Anl_TC_SM_2531_2_U_SPK8.indb 47 30.06.2021 08:18:5930.06.2021 08:18:59

EINHELL TC-SM 2531/2 U Specifications

General

Brand	EINHELL
Model	TC-SM 2531/2 U
Category	Saw
Language	English