EINHELL TC-TS 2025 U User Manual

GB
- 24 -
•
Stop rail
•
Leg (4x)
•
Longitudinal strut (2x)
•
Cross strut (2x)
•
Support (4x) *
•
Table width extension (2x)*
•
Hexagon screw (36x)
•
Spring washer (28x)
•
Washer (36x)
•
Nut (28x)
•
Ring wrench 10/13 mm
•
Ring wrench 10/21 mm
•
Suction hose
•
Original operating instructions
•
Safety information
* ) Only model TC-TS 2025 U with table width
extension
For production reasons, excess fastening mate-
rials (screws, etc.) may be supplied with models
TC-TS 2025 U and TC-TS 2025 eco.
3. Proper use
The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with the
machine‘s size. The equipment is not to be used
for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment‘s potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine‘s construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
4. Technical data
4.1 TC-TS 2025 U
AC motor .............................. 220-240V ~ 50Hz
Power P ...................S1 1800 W S6 25% 2000 W
Idle speed n
0
.......................................5000 min
-1
Cutting-off wheel .............Ø 250 x Ø 30 x 2.8 mm
Number of teeth .............................................. 24
Table size ......................................640 x 487 mm
Table width extension, left/right .....640 x 200 mm
Cutting height max. .......................... 85 mm / 90°
.......................................................... 65 mm / 45°
Height adjustment ..................... infi nite 0 -85 mm
Tilting saw blade .......................... infi nite 0° - 45°
Extractor socket ....................................Ø 36 mm
Weight............................................. approx. 21 kg
Protection class: ........................................... II/
쓑
Thickness of the splitter .......................... 2.0 mm
Anl_TC_TS_2025_U_2025_ECO_SPK1.indb 24Anl_TC_TS_2025_U_2025_ECO_SPK1.indb 24 04.09.15 11:1504.09.15 11:15

EINHELL TC-TS 2025 U Specifications

General

Power	2000 W
Blade diameter	250 mm
Max cutting depth at 90°	85 mm
Max cutting depth at 45°	60 mm
Table size	640 x 487 mm
Number of saw teeth	48
Swivelling range of saw blade	0° - 45°
Height adjustment	0 - 85 mm
Diameter of suction adapter	36 mm
Working height	830 mm
No-load speed	5000 rpm