GB
- 26 -
6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Assembling the base frame
(Fig. 4-5)
•
Turn the saw upside down and place it on the
floor.
•
Use the washers (c) and the hex screws (a) to
fasten the 4 legs (29) loosely to the saw.
•
Now use the hex screws (a), the spring
washers (b), the washers (c) and the nuts (d)
to fasten the longitudinal struts (31) and the
cross-struts (30) loosely to the legs. Impor-
tant: The longer struts have to be used on the
sides.
•
Finally, tighten all screws and nuts on the
base frame.
•
Screw the additional legs (36) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 5).
•
Plug the rubber feet (13) onto the legs (29).
6.2 Assembling the table width extension
(Fig. 6)
•
Use the screws (a), the spring washers (b),
the nuts (d) and the washers (c) to fasten the
table width extensions (33) loosely to the saw
table (1).
•
Screw the supports (32) loosely onto the saw
housing and onto the table width extensions
(33) (Fig. 6).
•
Align the table width extensions (33) level
with the saw table.
•
Finally, tighten all screws.
6.3 Fitting / removing the saw blade guard
(Fig. 6)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Do not tighten the screw (15) too far – the bla-
de guard must be able to move freely.
•
To remove the saw blade guard, proceed in
reverse order.
Warning!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.4 Changing the table insert (Figure 8)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the 1 countersunk head screws (17).
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.5 Setting the splitter (Fig. 9,10)
•
Danger! Pull out the power plug.
•
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
•
Remove the saw blade guard (see 6.2).
•
Take out the table insert (6) (see 6.4).
•
Slacken the fixing screw (19).
•
Push up the splitter (5) until the gap between
the saw table (1) and the upper edge of the
splitter (5) equals approx. 10 cm.
•
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
•
Retighten the screw (19) and mount the table
insert (6) (Fig. 8).
6.6 Fitting/replacing the blade (Fig. 7)
•
Important! Pull out the power plug first.
•
Remove the table insert by undoing the two
countersunk head screws (see 6.4).
•
Undo the nut with a size 21 wrench on the
nut itself and a second fork wrench (size 10)
on the motor shaft to apply counter-pressure.
•
Important! Turn the nut in the direction of
rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the bla-
de at an angle.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Mount and fasten the new saw blade in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter (5) and the saw gu-
ard (2) (see 6.3., 6.5.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Anl_TC_TS_2025_U_2025_ECO_SPK1.indb 26Anl_TC_TS_2025_U_2025_ECO_SPK1.indb 26 04.09.15 11:1504.09.15 11:15
To Next Page
Loading...
Need help?
General
