EINHELL TE-TC 620 U User Manual

GB
- 16 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Additional safety instructions
•
Set up the machine on a level, non-slip floor.
Make sure that the machine does not wobble.
•
Check that the voltage on the rating plate is
the same as your supply voltage. Only then
are you to insert the power plug in the socket-
outlet.
•
Wear safety goggles.
•
Wear ear-muffs.
•
Wear safety gloves.
•
Never use cracked diamond cutting wheels.
Replace immediately.
•
Never use segmented cutting wheels.
•
Caution! The cutting wheel runs on after the
machine is switched off!
•
Never apply side pressure to the diamond
cutting wheel in order to bring it to a halt.
•
Notice! The diamond cutting wheel must be
cooled with water at all times.
•
Always pull out the power plug before chan-
ging the cutting wheel.
•
Use only suitable diamond cutting wheels.
•
Never leave the machine unattended in
rooms with children.
•
Always pull out the power plug before exami-
ning the electric motor compartment system
•
Disorder in the work area can easily lead to
accidents.
•
Make sure that you stand squarely and solidly
while working. Avoid abnormal body positions
and always keep your balance.
•
If the cutting wheel becomes jammed, switch
off the equipment and disconnect it from the
power supply; only then are you to remove the
workpiece.
2. Layout and items supplied
1. Feet
2. Diamond cutting wheel
3. Trough
4. Work table
5. Angle stop
6. Stop rail
7. Guide rail
8. Cutting wheel guard
9. Handle
10. Clamping screw for angle setting
11. Clamping screw for cutting wheel guard
12. Clamping screw
13. Cooling water pump
14. Hose
15. Motor
16. On/Off switch
17. Angle scale
18. Transport handle
19. Transport wheels
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Anl_TE_TC_620_U_SPK7.indb 16Anl_TE_TC_620_U_SPK7.indb 16 24.05.2017 13:49:2124.05.2017 13:49:21

EINHELL TE-TC 620 U Specifications

General

Bore size	- mm
Idle speed	3000 RPM
Diamond disc	Yes
Maximum power	900 W
Blade diameter	200 mm
Cutting length	620 mm
AC input voltage	230 V
AC input frequency	50 Hz
Cutting height @ 45°	25 mm
Cutting height @ 90°	30 mm
Cutting disc swivel angle	45 °
Continuous operating time @ maximum power	30 min

Weight and Dimensions

Depth	1013 mm
Width	455 mm
Height	460 mm
Weight	34400 g
Table depth	325 mm
Table width	610 mm
Package weight	38600 g