EINHELL TE-TC 620 U User Manual

GB
- 19 -
push it to the required position.
•
You can now move the machine head (29) by
the handle (9) to the rear.
•
Place a tile against the stop rail (6) and the
angle stop (5).
•
Switch on the machine.
•
Important: Wait until the cooling water has
reached the cutting wheel (2).
•
Move the machine head (29) by the handle
(9) slowly and smoothly forward through the
tile.
6.5 45° Diagonal cut (Fig. 11/13)
•
Set the angle stop (5) to 45°.
•
Cut as described in 6.4.
6.6 45° Lengthwise cut, “jolly cut” (Fig.14/15)
•
Loosen the star grip screw (10).
•
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
•
Retighten the star grip screw (10).
•
Cut as described in 6.4.
6.7 Changing the diamond cutting wheel
(Fig. 16)
•
Pull out the power plug!
•
Remove the screw (30).
•
Swing up the guard (8).
•
Place the wrench (31) on the motor shaft and
hold.
•
Using the wrench (34), loosen the flange nut
in the direction of rotation of the cutting wheel
(2). (Caution: Left-hand thread.)
•
Remove the outer flange (35) and the cutting
wheel (2).
•
Clean the mounting flange (35) thoroughly
before fitting the new cutting wheel.
•
Install the new cutting wheel in reverse order
and tighten.
•
Important: Pay attention to the direction of
rotation of the cutting wheel!
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Remove dust and dirt from the machine at
regular intervals. Cleaning is best carried out
with a rag or brush.
•
Never use caustic agents to clean plastic
parts.
•
The trough (3) and the cooling water pump
(13) must be cleaned at regular intervals or
proper cooling of the diamond cutting wheel
(2) will not be guaranteed.
8.2 Maintenance
Lubricate all moving parts at regular intervals.
8.3 Transport (Fig. 17)
•
If you want to move the equipment to a
different location, first undo the clamping
screws (12) and push them together with the
machine head (29) to the same side as the
transport wheels (19), then fasten the two
clamping screws (12) again.
•
Fold up the feet (1) one after the other, star-
ting ideally on the same side as the transport
wheels (19) in order not to overload the trans-
port handle (18) when putting the equipment
down.
•
You can now transport the equipment by the
transport handle (18).
•
You can park the equipment in minimum
space as shown. When doing so, put your
foot on the axle to prevent the equipment
rolling away.
Anl_TE_TC_620_U_SPK7.indb 19Anl_TE_TC_620_U_SPK7.indb 19 24.05.2017 13:49:2124.05.2017 13:49:21

EINHELL TE-TC 620 U Specifications

General

Bore size	- mm
Idle speed	3000 RPM
Diamond disc	Yes
Maximum power	900 W
Blade diameter	200 mm
Cutting length	620 mm
AC input voltage	230 V
AC input frequency	50 Hz
Cutting height @ 45°	25 mm
Cutting height @ 90°	30 mm
Cutting disc swivel angle	45 °
Continuous operating time @ maximum power	30 min

Weight and Dimensions

Depth	1013 mm
Width	455 mm
Height	460 mm
Weight	34400 g
Table depth	325 mm
Table width	610 mm
Package weight	38600 g