EasyManua.ls Logo

elco VG 2.210 D - User Manual

elco VG 2.210 D
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
02/2011 - Art. Nr. 4200 1029 5200B
VG 2.120 D
VG 2.160 D
VG 2.210 D
Operating instructions
For specialist installation engineers
Gas burners ........................................... 2-28
en
de, fr..................................... 4200 1029 5000
it, nl ...................................... 4200 1029 5100
............................................. 4200 1029 4901

Table of Contents

Questions and Answers

  • W
    whitesusanAug 8, 2025
    What to do if elco VG 2.210 D starts, the ignition switches on, then failure?
    • J
      jamesbrownAug 8, 2025
      If the Elco Burner starts, the ignition switches on, then fails, it could be due to several reasons: no flame at the end of the safety time, incorrect gas throughput, malfunction in the flame monitoring system, incorrect polarisation of the power supply, no ignition sparks, short-circuited electrodes, damaged ignition cables, defective igniter, control and safety unit issues or valves jamming. To address this, adjust the gas flow, check the ionisation probe's condition and position, verify the ionisation circuit connections, ensure correct polarisation of the 7P connector, adjust, clean or replace the electrodes, connect or replace the cable(s), replace the igniter, replace the control unit, check the cabling, replace the compact gas unit, and/or replace the valves.
  • D
    dmasonAug 12, 2025
    Why does elco VG 2.210 D switch off during operation?
    • N
      nicholas48Aug 13, 2025
      The Elco Burner might switch off during operation because of the air pressure switch contact opening during start-up or operation, or due to flame failure during operation. Try adjusting or replacing the pressure switch, checking the ionisation probe circuit, or checking or replacing the control and safety unit.
  • J
    John EdwardsAug 18, 2025
    What to do if elco VG 2.210 D Burner does not start after thermostatic closure?
    • W
      william19Aug 18, 2025
      If the Elco Burner doesn't start after thermostatic closure, this could be due to a drop in supply voltage, a power failure, or a control unit malfunction. Check the cause of the voltage drop or power failure and replace the control unit.
  • R
    Roy SotoAug 23, 2025
    What to do if elco VG 2.210 D Burner blower starts up, but burner does not start because of flaring?
    • S
      shepherdtrevorAug 23, 2025
      If the Elco Burner blower starts but the burner doesn't due to flaring during pre-ventilation or pre-ignition, check the valve and flame monitoring.
  • W
    Wyatt FowlerAug 28, 2025
    Why elco VG 2.210 D Burner has no heat requested?
    • S
      Sean ZhangAug 28, 2025
      If there is no heat requested from the Elco Burner, the thermostats could be defective or incorrectly adjusted. Adjust the thermostats, and replace them if necessary.
  • G
    George WolfeSep 2, 2025
    What causes a servomotor fault in Elco Burner?
    • C
      Caroline HatfieldSep 2, 2025
      A servomotor fault in the Elco Burner could be due to clogging or locking of the air flap, or an internal fault with the servomotor. Replace the servomotor.

Summary

Operation

TCG 2 xx Control Unit Interface

Overview of the TCG 2xx control unit's display, buttons, and locking/unlocking features.

Terminal Allocation Charts

Diagrams and lists detailing electrical terminal connections for the burner.

MB-ZRDLE Gas Train Technical Data and Settings

Specifications and adjustment procedures for the MB-ZRDLE gas train components.

Assembly

Gas Connection and Pre-Commissioning Checks

Guidelines for gas connection, electrical hookup, and essential checks before commissioning.

Commissioning

Adjustment Data and Pressure Switch Settings

Table of burner adjustment values and procedures for setting gas and air pressure switches.

Setting the MB-ZRDLE Gas Train and Regulator

Detailed steps for adjusting the gas train regulator, incremental advance, and 1st/2nd stage flow.

Pre-Setting Without Flame and Servomotor Value Modification

Optimizing Combustion Values and Function Checks

Setting the Flame and Operating Mode

Servicing

Annual Maintenance Tasks and General Checks

Malfunction Diagnosis and Troubleshooting

elco VG 2.210 D Specifications

General IconGeneral
Brandelco
ModelVG 2.210 D
CategoryBurner
LanguageEnglish

Related product manuals