Electro-Voice ELX200-10

Questions and Answers

K
Kenneth SteeleJul 28, 2025
How to troubleshoot no sound from Electro-Voice Speakers?
- D
  David WilsonJul 28, 2025
  If your Electro-Voice speakers have no sound, there could be a problem with the amplifier or the wiring. First, connect a working test loudspeaker to the amplifier outputs to check if the amplifier is the issue. If there's still no sound, ensure all electronics are on, the signal routing is correct, the source is active, and the volume is turned up. If the amplifier works, the problem is likely in the wiring. Check the cables connected to the amplifier. Play something quietly and connect the test loudspeaker in parallel with the malfunctioning line. If the sound disappears or is very weak, there's a short in the line. Use the test loudspeaker to check each connection until you find and fix the problem, ensuring correct polarity.
J
jaustinAug 4, 2025
Why do my Electro-Voice Speakers have constant buzzing noise?
- C
  Christine VegaAug 4, 2025
  If your Electro-Voice speakers are producing constant noise like buzzing, hissing, or humming, the issue might be a defective source, another electronic device, or a problem with system grounding. If the noise is present even when no program material is playing, evaluate each component to isolate the problem, as there's likely a break in the signal path. Additionally, check and correct the system grounding as needed to resolve any ground loop issues.
S
Sandra IbarraAug 11, 2025
What to do if Electro-Voice ELX200-10 have cracking sound?
- T
  Taylor FernandezAug 11, 2025
  If your Electro-Voice speakers have intermittent output, such as cracking or distortion, the cause may be a faulty connection. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem persists, check the wiring.
C
Calvin FarleyAug 19, 2025
Why do Electro-Voice Speakers have poor bass response?
- P
  Peggy WeberSep 12, 2025
  If your Electro-Voice speakers have poor low-frequency response, it might be due to the loudspeakers being wired out-of-polarity. When two loudspeakers are connected out of polarity, the low frequencies will cancel each other acoustically. Check the wire markings or tracers on your loudspeaker wires. Make sure the amplifier (+) terminal connects to pin 1+ of the NL4 connector and the amplifier (-) terminal connects to pin 1- of the NL4 connector.

Summary

Safety

Important Safety Instructions

General safety instructions for installation and use.

Suspension Safety

Warning and precautions for suspending loudspeakers.

Operational Precautions

Environmental and operational precautions for loudspeakers.

Notices

Information on recycling old appliances and copyright.

Product Description

System Features

Detailed features of the ELX200 series loudspeakers.

Operation Modes

Tripod or Pole Mounting

Instructions for mounting loudspeakers on tripods or poles.

Floor Monitor Setup

Guidance on using loudspeakers as floor monitors.

Suspension System

Suspension Points and Eyebolt Installation

Details on suspension points and how to install eyebolts.

Recommended Configurations

Basic Stereo System

Wiring diagram for a basic stereo system setup.

Stage Monitor Configuration

Configuration for using loudspeakers as stage monitors.

Stacking with Subwoofers

Connecting full-range systems with subwoofers for enhanced bass.

Troubleshooting

Common Audio Issues and Solutions

Common problems and solutions for audio issues.

Technical Data

Specifications for ELX200-10, -12, -15

Technical specifications for ELX200-10, ELX200-12, and ELX200-15.

Specifications for ELX200-12 S, -18 S

Technical specifications for ELX200-12S and ELX200-18S.

Dimensions and Diagrams

Physical dimensions and diagrams for ELX200 models.

Frequency Response and Impedance Graphs

Frequency response and impedance graphs for ELX200 series.

Electro-Voice ELX200-10 Specifications

General

Speaker type	2-way
Number of drivers	-
Speaker placement	Floor
Audio output channels	2.0 channels
Woofer diameter (imperial)	10 \
Impedance	8 Ω
Sensitivity	127 dB
Frequency range	49 - 22000 Hz
RMS rated power	300 W
Crossover frequency	2000 Hz
Peak Music Power Output (PMPO)	1200 W
Plug and Play	Yes
Product color	Black
Housing material	Polypropylene (PP)
Recommended usage	Speaker set unit
Connectivity technology	Wired
Package type	Box
Package weight	15300 g