Electro-Voice ELX200 - User Manual

Other manuals for Electro-Voice ELX200

Questions and Answers

S
scochranAug 19, 2025
Why do my Electro-Voice ELX200 Speakers have no sound?
- P
  paullindseyAug 19, 2025
  If your Electro-Voice speakers aren't producing sound, there could be several reasons. First, verify that all electronic components are powered on, the signal routing is correctly configured, the audio source is active, and the volume is appropriately adjusted. If there is still no sound, the issue might stem from the wiring. Make sure the correct cables are connected to the amplifier. Play audio at a low level through the amplifier, then connect a test loudspeaker in parallel with the malfunctioning line. If the sound disappears or becomes very weak, the line likely has a short circuit. Use the test loudspeaker to check each connection until you identify and fix the problem, ensuring correct polarity.
S
Sarah BrownAug 21, 2025
How to stop acoustic feedback from Electro-Voice Speakers when using a microphone?
- A
  Ashley EvansAug 21, 2025
  To stop acoustic feedback from your Electro-Voice speakers when using a microphone, you can take several steps. First, reduce the microphone levels at the mixing console or input source. If the microphone is directly connected to the speaker, lower the input level on the speaker. Positioning the microphone closer to the sound source can increase gain-before-feedback. Also, if the MODE is set to MUSIC, change it to LIVE or SPEECH. Finally, position the loudspeakers so the microphone is behind them whenever possible. If using the loudspeaker in a monitor position, aim the loudspeaker to the back of the microphone.
G
George SellersAug 25, 2025
Why are my Electro-Voice ELX200 Speakers making a constant buzzing noise?
- C
  Chloe TorresAug 25, 2025
  Constant noise such as buzzing, hissing, or humming from your Electro-Voice speakers can stem from several causes. It could be a defective source or another electronic device; if the noise is present even when no program material is playing, evaluate each component to isolate the problem, as there's likely a break in the signal path. Poor system grounding or a ground loop can also cause this issue, so check and correct the system grounding as needed. Additionally, ensure the input gain knob is properly adjusted; slowly increase the input gain knob level to engage the microphone pre-amp.
L
Lisa VelasquezAug 26, 2025
Why do my Electro-Voice ELX200 Speakers have intermittent cracking?
- G
  Gregory AdamsAug 26, 2025
  Intermittent output, such as cracking or distortion in your Electro-Voice speakers, is often due to a faulty connection. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem persists, inspect the wiring.
T
Tammie OnealAug 28, 2025
Why is there no sound from my Electro-Voice ELX200 when using a microphone?
- M
  markmcdonaldAug 28, 2025
  If no sound is produced when a microphone is connected to INPUT 1 or INPUT 2 on your Electro-Voice speakers, it could be due to a couple of reasons. The microphone might require phantom power; if so, use a dynamic microphone that doesn't need it, or use an external phantom power source. Also, ensure the input gain knob is properly adjusted by slowly increasing the input gain knob level to engage the microphone pre-amp.
S
Samuel NicholsAug 30, 2025
How to unlock the DSP menu on Electro-Voice ELX200?
- W
  Willie RodriguezAug 30, 2025
  If the DSP menu on your Electro-Voice speakers is locked (indicated by a lock symbol on the LCD screen), it means the Menu Lock function has been activated. To unlock it, press and hold the MASTER VOL knob for 5 seconds.
K
Kenneth Mcgee DDSSep 1, 2025
Why do my Electro-Voice ELX200 Speakers produce acoustic feedback?
- R
  Rachel GonzalezSep 1, 2025
  If your Electro-Voice Speakers produce acoustic feedback when the input level is amplified, there are several potential causes. First, the gain structure may be incorrect; try reducing the microphone levels at the mixing console or input source, or if the microphone is directly connected to the speaker, reduce the input level on the speaker. Positioning the microphone closer to the sound source can also help increase gain-before-feedback. Second, ensure the MODE is set to LIVE or SPEECH, not MUSIC. Finally, adjust the loudspeaker setup so the microphone is behind them, or if using the loudspeaker in a monitor position, aim the loudspeaker to the back of the microphone.
W
William CamachoSep 3, 2025
Why are my Electro-Voice ELX200 hissing?
- P
  Paul TaylorSep 3, 2025
  If your Electro-Voice Speakers produce a constant noise such as buzzing, hissing, or humming, several factors could be responsible. The noise could be caused by a defective source or other electronic device; evaluate each component to isolate the problem, as there is likely a break in the signal path. Alternatively, the issue could stem from poor system grounding or a ground loop, so check and correct the system grounding as required. Also, ensure the input gain knob is not in the MIC position; slowly increase the input gain knob level to engage the microphone pre-amp.
D
David EvansSep 5, 2025
What to do if Electro-Voice ELX200 Speakers have no sound with microphone?
- J
  joneskathrynSep 5, 2025
  If your Electro-Voice Speakers aren't producing sound when a microphone is connected to INPUT 1 or INPUT 2, the issue might be related to the microphone itself or the input settings. If the microphone requires phantom power, either use a dynamic microphone that doesn't need it, or use an external phantom power source. Also, make sure the input gain knob is not in the MIC position; slowly increase the input gain knob level to engage the microphone pre-amp.
J
Jason FrostSep 7, 2025
How to fix Electro-Voice ELX200 with cracking sound?
- A
  Amber FisherSep 7, 2025
  If your Electro-Voice Speakers have intermittent output with cracking or distortion, a faulty connection could be the cause. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem persists, inspect the wiring as described in the 'No Sound' troubleshooting section.

The Electro-Voice ELX200-18SP is an 18-inch powered subwoofer designed for both portable and installed applications, offering high-efficiency and robust performance. Its primary function is to extend the low-frequency response of a sound system, delivering powerful and clear bass.

Function Description:

The ELX200-18SP features a high-efficiency 1200 W Class-D power amplifier, capable of delivering up to 132 dB peak SPL. This power is channeled through an 18-inch EVS-18L transducer, specifically designed and engineered by Electro-Voice for optimal performance. The subwoofer integrates QuickSmartDSP, a best-in-class digital signal processing unit that simplifies setup and control. Users can choose from three presets (Music, Live, Club) for quick configuration, or utilize five user-programmable presets for customized settings. The DSP also includes sub/top system-match crossovers, a three-band EQ, and visual monitoring of limiter status, input level, and master volume control, all accessible via an LCD interface. This comprehensive control ensures optimal gain structure and sound quality.

For enhanced usability, the ELX200-18SP supports the EV QuickSmart Mobile application, which allows for wireless configuration, control, and monitoring of up to six ELX200 loudspeakers simultaneously. This application, utilizing Bluetooth® Low Energy (BTLE) technology, provides intuitive system control and immediate notifications for critical performance conditions, such as overdriving. This feature allows users to manage their sound system from in front of the speakers, rather than being confined to the rear panel.

Important Technical Specifications:

Frequency Response (-3 dB): 47 Hz – 105 Hz
Frequency Range (-10 dB): 40 Hz – 145 Hz
Maximum SPL: 132 dB
Power Rating: 1200 W
LF Transducer: EVS-18L 457 mm (18 in)
Low-Pass Frequency: Adjustable (80 Hz, 100 Hz, 120 Hz, 150 Hz)
Connectors: (2) XLR/TRS combo jacks (inputs) and (2) XLR link outputs
Enclosure: 15 mm plywood with EVCoat finish
Grille: 18 AWG steel with powdercoat
Color: Black
Dimensions (H x W x D): 600 mm x 507 mm x 574 mm (23.7 in x 20.0 in x 22.6 in)
Net Weight: 29.0 kg (64 lb)
Shipping Weight: 33.1 kg (73.0 lb)
Power Consumption: 100 - 240 V~, 50-60 Hz, 1.8 A (1/8 power)

Usage Features:

The ELX200-18SP is designed for ease of use and versatility. Its integrated M20 threaded pole mount plate allows for secure mounting of full-range loudspeakers, making it suitable for stacked setups. The two-handle design facilitates easy lifting and transport, supporting its use in portable sound reinforcement.

The rear amplifier panel provides clear access to all controls and connections. The LCD screen serves as the DSP control and monitoring interface, allowing users to navigate menus and adjust settings using the MASTER VOL knob. Input signals are connected via balanced XLR/TRS combo jacks, and XLR link outputs enable the signal to be sent to additional loudspeakers or subwoofers. The power switch and IEC-connector for AC mains input are also conveniently located.

The QuickSmart Mobile application significantly enhances the user experience by providing remote control capabilities. This allows for quick adjustments and monitoring of the system from anywhere within range, which is particularly useful in live sound environments where precise control and real-time feedback are crucial. The ability to receive immediate notifications for critical performance conditions helps prevent damage and ensures consistent sound quality.

Maintenance Features:

While the manual does not explicitly detail maintenance features, the robust construction of the ELX200-18SP suggests durability and reliability. The 15 mm plywood enclosure with EVCoat finish and the 18 AWG steel grille with powdercoat are designed to withstand the rigors of both portable use and permanent installations. The use of high-quality components and engineering by Electro-Voice implies a product built for longevity.

For specific maintenance or troubleshooting, the manual refers users to the ELX200 Powered Loudspeakers Installation manual (F.01U.326.891), indicating that detailed instructions for upkeep and problem-solving would be found there. The modular design, with accessible amplifier panel and standard connectors, suggests that any necessary servicing or component replacement would be straightforward for qualified technicians. The system's self-monitoring capabilities, such as limiter status display, also contribute to proactive maintenance by alerting users to potential issues before they escalate.