Electro-Voice ELX200 User Manual (English)

Other manuals for Electro-Voice ELX200

Questions and Answers:

S
scochranAug 19, 2025
Why do my Electro-Voice ELX200 Speakers have no sound?
- P
  paullindseyAug 19, 2025
  If your Electro-Voice speakers aren't producing sound, there could be several reasons. First, verify that all electronic components are powered on, the signal routing is correctly configured, the audio source is active, and the volume is appropriately adjusted. If there is still no sound, the issue might stem from the wiring. Make sure the correct cables are connected to the amplifier. Play audio at a low level through the amplifier, then connect a test loudspeaker in parallel with the malfunctioning line. If the sound disappears or becomes very weak, the line likely has a short circuit. Use the test loudspeaker to check each connection until you identify and fix the problem, ensuring correct polarity.
S
Sarah BrownAug 21, 2025
How to stop acoustic feedback from Electro-Voice Speakers when using a microphone?
- A
  Ashley EvansAug 21, 2025
  To stop acoustic feedback from your Electro-Voice speakers when using a microphone, you can take several steps. First, reduce the microphone levels at the mixing console or input source. If the microphone is directly connected to the speaker, lower the input level on the speaker. Positioning the microphone closer to the sound source can increase gain-before-feedback. Also, if the MODE is set to MUSIC, change it to LIVE or SPEECH. Finally, position the loudspeakers so the microphone is behind them whenever possible. If using the loudspeaker in a monitor position, aim the loudspeaker to the back of the microphone.
G
George SellersAug 25, 2025
Why are my Electro-Voice ELX200 Speakers making a constant buzzing noise?
- C
  Chloe TorresAug 25, 2025
  Constant noise such as buzzing, hissing, or humming from your Electro-Voice speakers can stem from several causes. It could be a defective source or another electronic device; if the noise is present even when no program material is playing, evaluate each component to isolate the problem, as there's likely a break in the signal path. Poor system grounding or a ground loop can also cause this issue, so check and correct the system grounding as needed. Additionally, ensure the input gain knob is properly adjusted; slowly increase the input gain knob level to engage the microphone pre-amp.
L
Lisa VelasquezAug 26, 2025
Why do my Electro-Voice ELX200 Speakers have intermittent cracking?
- G
  Gregory AdamsAug 26, 2025
  Intermittent output, such as cracking or distortion in your Electro-Voice speakers, is often due to a faulty connection. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem persists, inspect the wiring.
T
Tammie OnealAug 28, 2025
Why is there no sound from my Electro-Voice ELX200 when using a microphone?
- M
  markmcdonaldAug 28, 2025
  If no sound is produced when a microphone is connected to INPUT 1 or INPUT 2 on your Electro-Voice speakers, it could be due to a couple of reasons. The microphone might require phantom power; if so, use a dynamic microphone that doesn't need it, or use an external phantom power source. Also, ensure the input gain knob is properly adjusted by slowly increasing the input gain knob level to engage the microphone pre-amp.
S
Samuel NicholsAug 30, 2025
How to unlock the DSP menu on Electro-Voice ELX200?
- W
  Willie RodriguezAug 30, 2025
  If the DSP menu on your Electro-Voice speakers is locked (indicated by a lock symbol on the LCD screen), it means the Menu Lock function has been activated. To unlock it, press and hold the MASTER VOL knob for 5 seconds.
K
Kenneth Mcgee DDSSep 1, 2025
Why do my Electro-Voice ELX200 Speakers produce acoustic feedback?
- R
  Rachel GonzalezSep 1, 2025
  If your Electro-Voice Speakers produce acoustic feedback when the input level is amplified, there are several potential causes. First, the gain structure may be incorrect; try reducing the microphone levels at the mixing console or input source, or if the microphone is directly connected to the speaker, reduce the input level on the speaker. Positioning the microphone closer to the sound source can also help increase gain-before-feedback. Second, ensure the MODE is set to LIVE or SPEECH, not MUSIC. Finally, adjust the loudspeaker setup so the microphone is behind them, or if using the loudspeaker in a monitor position, aim the loudspeaker to the back of the microphone.
W
William CamachoSep 3, 2025
Why are my Electro-Voice ELX200 hissing?
- P
  Paul TaylorSep 3, 2025
  If your Electro-Voice Speakers produce a constant noise such as buzzing, hissing, or humming, several factors could be responsible. The noise could be caused by a defective source or other electronic device; evaluate each component to isolate the problem, as there is likely a break in the signal path. Alternatively, the issue could stem from poor system grounding or a ground loop, so check and correct the system grounding as required. Also, ensure the input gain knob is not in the MIC position; slowly increase the input gain knob level to engage the microphone pre-amp.
D
David EvansSep 5, 2025
What to do if Electro-Voice ELX200 Speakers have no sound with microphone?
- J
  joneskathrynSep 5, 2025
  If your Electro-Voice Speakers aren't producing sound when a microphone is connected to INPUT 1 or INPUT 2, the issue might be related to the microphone itself or the input settings. If the microphone requires phantom power, either use a dynamic microphone that doesn't need it, or use an external phantom power source. Also, make sure the input gain knob is not in the MIC position; slowly increase the input gain knob level to engage the microphone pre-amp.
J
Jason FrostSep 7, 2025
How to fix Electro-Voice ELX200 with cracking sound?
- A
  Amber FisherSep 7, 2025
  If your Electro-Voice Speakers have intermittent output with cracking or distortion, a faulty connection could be the cause. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem persists, inspect the wiring as described in the 'No Sound' troubleshooting section.