EVID
EVID
TMTM
Owner’s ManualOwner’s Manual
55
Figure 8:Figure 8: Wattage Taps (4.2t & 6.2t)Wattage Taps (4.2t & 6.2t)
Product DescriptionProduct Description
Step 2: Select Wattage TapStep 2: Select Wattage Tap
(Models 4.2t and 6.2t Only)(Models 4.2t and 6.2t Only)
Before mounting the speaker to theBefore mounting the speaker to the
bracket, select the proper wattage tapbracket, select the proper wattage tap
setting for your installation. The wattagesetting for your installation. The wattage
selector switch is located at the rear of theselector switch is located at the rear of the
speaker below the input terminal panel.speaker below the input terminal panel.
The EVID™ 4.2t and 6.2t include a switchThe EVID™ 4.2t and 6.2t include a switch
for selecting the power taps. The EVID™for selecting the power taps. The EVID™
3.2t has a single power tap.3.2t has a single power tap.
EVID™ 3.2tEVID™ 3.2t
A single (non-selectable) power tap ratedA single (non-selectable) power tap rated
at 5W@70V and 10W@100V.at 5W@70V and 10W@100V.
EVID™ 4.2tEVID™ 4.2t
The power taps are 30W, 15W and 7.5WThe power taps are 30W, 15W and 7.5W
at both 70.7V and 100V, with a 3.7W tapat both 70.7V and 100V, with a 3.7W tap
for 70.7V only, as well as an 8 ohmfor 70.7V only, as well as an 8 ohm
transformer bypass setting.transformer bypass setting.
EVID™ 6.2t:EVID™ 6.2t:
The power taps are 60W, 30W and 15WThe power taps are 60W, 30W and 15W
at both 70.7V and 100V, with a 7.5W tapat both 70.7V and 100V, with a 7.5W tap
for 70.7V only, as well as an 8 ohmfor 70.7V only, as well as an 8 ohm
transformer bypass setting.transformer bypass setting.
The taps for the models listed above areThe taps for the models listed above are
selected by a rotary switch on the backselected by a rotary switch on the back
panel. A panel. A guide on the guide on the back of eachback of each
speaker shows which switch positions tospeaker shows which switch positions to
use for the power settings at 70V anduse for the power settings at 70V and
100V.100V.
Figure 8 below illustrates the settings forFigure 8 below illustrates the settings for
the 4.2t and 6.2t.the 4.2t and 6.2t.
Step 3: Mount the Speaker to theStep 3: Mount the Speaker to the
SAM™ BracketSAM™ Bracket
Attach the speaker to the SAM™ bracketAttach the speaker to the SAM™ bracket
with the socket head bolt B, as shown inwith the socket head bolt B, as shown in
Figure 9.Figure 9.
Figure 10:Figure 10: Recommended TorqueRecommended Torque
Settings for Bolt ASettings for Bolt A
Using the provided security tool, tightenUsing the provided security tool, tighten
the two socket head bolts shown in Fig.the two socket head bolts shown in Fig.
9. 9. Select the Select the proper horizontal proper horizontal angle andangle and
secure it by tightening Bolt A to the propersecure it by tightening Bolt A to the proper
torque listed torque listed in Fig. 10. in Fig. 10. Then selecThen select thet the
proper vertical angle and secure it byproper vertical angle and secure it by
tightetightening Bolt B. ning Bolt B. Use the Use the 15° 15° angleangle
markers as your guide (see Fig. 9). Attachmarkers as your guide (see Fig. 9). Attach
both logo caps as shown in Figure 11both logo caps as shown in Figure 11
after tightening and securing the speaker.after tightening and securing the speaker.
4.2t4.2t
6.2t6.2t
Figure 11:Figure 11: Attach Logo CapsAttach Logo Caps
EV logo capEV logo cap
(large)(large)
EV logo capEV logo cap
(small)(small)
Figure 9:Figure 9: Tighten Socket Head BoltsTighten Socket Head Bolts
Bolt ABolt A
(swing)(swing)
Bolt BBolt B
(rotation)(rotation)
15˚ angle markers15˚ angle markers
MMooddeell TToorrqquuee
EEVVIID D 33..22 2020-3-30 i0 in-n-lblbs (s (2.2.3-3-33.4 .4 NN-m-m))
EEVVIID D 44..22 3030-5-50 i0 in-n-lblbs (s (3.3.4-4-55.2 .2 NN-m-m))
EEVVIID D 66..22 7070-9-90 i0 in-n-lblbs (s (7.7.9-9-110.0.2 N2 N-m-m))
To Next Page
Loading...
