Electro-Voice EVL-ZLX-12P-BT

Questions and Answers

C
Christopher AdamsSep 5, 2025
How to stop buzzing, hissing, or humming noise from Electro-Voice EVL-ZLX-12P-BT?
- R
  Raymond DunlapSep 5, 2025
  Constant noise like buzzing, hissing, or humming from Electro-Voice speakers can stem from a few sources: * **Defective source:** If noise is present without program material playing, evaluate each component to isolate the problem. A break in the signal path is likely. * **Grounding issues:** Check and correct the system grounding, as required. * **Input gain knob:** Slowly increase the input gain knob level to engage the microphone pre-amp.
T
Thomas MurphyNov 26, 2025
Why is there no sound coming from my Electro-Voice EVL-ZLX-12P-BT Speakers?
- B
  benjamingregoryNov 27, 2025
  If there is no sound coming from your Electro-Voice speakers, connect a known working test speaker to the amplifier outputs. If there is still no sound, check that all the electronics are on, the signal routing is correct, the source is active, and the volume is turned up. Correct, repair, or replace components as necessary. If there is sound from the test speaker, the problem is in the wiring. Verify that you have connected the correct wire pairs to the amplifier. Play something at low level through the amplifier (for example, from an MP3 device). Connect the test speaker in parallel with the malfunctioning line. If the sound level has gone or is very weak, the line has a short in it. If the sound level is normal, the wire is open. Using the test speaker, move down the line and test each ...
C
Cheryl ThomasSep 18, 2025
How to unlock the DSP menu on Electro-Voice Speakers?
- T
  Tommy VasquezSep 18, 2025
  If the DSP menu on your Electro-Voice speakers is locked (indicated by a lock symbol on the LCD screen), the Menu Lock function has been turned on. To unlock it, press and hold the MASTER VOL knob for 5 seconds.
S
Sean ThorntonSep 16, 2025
What to do if Electro-Voice EVL-ZLX-12P-BT Speakers have poor low-frequency response?
- H
  hendrickscarlySep 16, 2025
  If you notice poor low-frequency response from your Electro-Voice speakers, and the SUB menu cross-over frequency is activated, but no subwoofers are used with the system, select the OFF position.
M
Mrs. Madison CarrollSep 14, 2025
Why does streaming audio skip or stutter on my Electro-Voice EVL-ZLX-12P-BT?
- M
  Matthew AlexanderSep 14, 2025
  Skipping or stuttering playback during streaming audio on your Electro-Voice speakers can be due to: * **Distance:** Move the paired mobile device closer to the loudspeaker. * **Interference:** This Bluetooth enabled loudspeaker occupies the same operating frequencies as other Bluetooth devices, as well as Wi-Fi and other wireless transmissions (like wireless home phones). If you are experiencing drop- outs, your speaker may be in an environment that makes reliable wireless audio difficult. Try to move the loudspeaker to different locations in the room, and especially away from 2.4gHz routers and microphone receivers. If the problem persists, revert back to a wired connection while at that particular venue.
S
Stephen SmithSep 12, 2025
What causes cracking or distortion in Electro-Voice EVL-ZLX-12P-BT Speakers output?
- C
  Chad CortezSep 13, 2025
  Intermittent output, like cracking or distortion, from Electro-Voice speakers often points to a faulty connection. Check all connections at the amplifier and loudspeakers to ensure they are clean and tight. If the problem continues, inspect the wiring as described in the troubleshooting for 'no sound'.
K
Keith DaltonSep 12, 2025
Why is there no sound with a microphone connected to Electro-Voice Speakers?
- E
  ericcampbellSep 12, 2025
  If no sound is produced when a microphone is connected to INPUT 1 or INPUT 2 on your Electro-Voice speakers, there are a couple of possibilities: * **Phantom power:** Use a dynamic microphone that does not require phantom power. If using a microphone requiring phantom power, an external phantom power source is needed. * **Input gain knob:** Slowly increase the input gain knob level to engage the microphone pre-amp.
T
Terry GuzmanSep 9, 2025
Why is there no streaming audio from my Electro-Voice Speakers?
- P
  Peter WalkerSep 9, 2025
  If you're experiencing no streaming audio with your Electro-Voice speakers, consider the following: * **STREAMING is OFF:** Set STREAMING to PAIRING and initiate the Bluetooth pairing process on your mobile device. * **Mobile device paired incorrectly:** If previously paired to a different Bluetooth enabled ZLX loudspeaker, you may be pairing with the wrong device. Try deleting all saved connections labeled EV ZLX BT and try the pairing process again. * **Input level too low:** While music is playing, turn up the volume on the paired mobile device. You will see the BT VU Meter receiving signal. Reduce if you see a CLIP notification. * **Output Gain is too low:** Increase output gain by setting your LEVEL with the MASTER VOL knob, paying attention to CLIP and LIMIT notifications.
C
Christina ArnoldSep 7, 2025
What to do if Electro-Voice EVL-ZLX-12P-BT Speakers sound distorted and the LIMIT light is on?
- A
  amandagraySep 7, 2025
  If the sound from your Electro-Voice speakers is distorted, the front LED is off, and the LCD screen shows 'LIMIT' is on, it indicates an excessive input level. Reduce the input level or loudspeaker level knobs to prevent limiting.
D
Derek NguyenAug 20, 2025
Why is my Electro-Voice speaker sound distorted and the LCD screen shows LIMIT?
- O
  Oscar WilliamsAug 21, 2025
  The sound distortion and the 'LIMIT' indication on the LCD screen of your Electro-Voice speaker usually means there's an excessive input level. Reduce the input level or loudspeaker level knobs to prevent limiting. It can also happen if the gain structure is incorrect or the source input (mixing console/ preamp) is overdriven. Check the level controls of the source using the VU meter on the LCD screen. If the VU meter bar is solid or the system indicates LIMIT, the input or source level is too high.