Why is the bass weak on my Electro-Voice ZxA1-Sub?
If you are experiencing poor low-frequency response with your Electro-Voice ZxA1-Sub, the polarity might be incorrect. Set the NORMAL/REVERSE POLARITY switch to the opposite position.
How to improve low-frequency response on Electro-Voice ZxA1 Speakers?
If you notice a poor low-frequency response with your Electro-Voice ZxA1 speakers, check the FULL RANGE/WITH SUB switch. Ensure it is set to the FULL RANGE position.
Why is there no sound from the microphone connected to MIC IN on Electro-Voice ZxA1-Sub?
If no sound is produced when a microphone is connected to the MIC IN of your Electro-Voice speakers, the microphone might require phantom power. Use a dynamic microphone that does not require phantom power or, if using a microphone that requires it, use an external phantom power source.
Why do Electro-Voice Speakers sound distorted when LIMIT LED is off?
If your Electro-Voice speakers are producing distorted sound and the LIMIT LED is not blinking, the source input (mixing console/preamp) might be overdriven. Verify that the level controls of the source are properly structured.
What to do if Electro-Voice ZxA1-Sub have crackling sound?
If you're experiencing intermittent output, such as crackling or distortion, from your Electro-Voice speakers, a faulty connection is a likely cause. Check all connections at the amplifier and speakers to ensure they are clean and tight. If the problem persists, it may be in the amplifier or wiring. Refer to the troubleshooting steps for 'No Sound'.
How to stop microphone feedback with Electro-Voice Speakers?
If your microphone produces acoustic feedback when the input level is amplified through your Electro-Voice speakers, the issue likely stems from incorrect gain structure or microphone placement. Try these solutions: * Reduce the microphone levels at the mixing console or input source. If the microphone is connected directly to the speaker, reduce the MIC LEVEL on the speaker. Positioning the microphone close to the sound source will increase gain-before-feedback. * Whenever possible, set up the speakers so the microphone is behind them. If using the speakers in a monitor position, aim the speaker to the back of the microphone.
What to do if Electro-Voice ZxA1-Sub sound distorted and LIMIT LED is on?
If the sound from your Electro-Voice speakers is distorted and the LIMIT LED is constantly on or flashing regularly, it could be due to excessive input level or incorrect input connection. Try these solutions: * Reduce the Master Level or loudspeaker level knobs to prevent limiting. * Ensure that line-level sources are plugged into the LINE IN, not the MIC IN.
General| Subwoofer type | Active subwoofer |
|---|---|
| Number of subwoofers | 1 |
| Subwoofer sensitivity | 126 dB |
| Subwoofer driver diameter | 305 mm |
| Subwoofer frequency range | 44 - 118 Hz |
| Subwoofer crossover frequencies | 100 - 100 Hz |
| Subwoofer driver diameter (imperial) | 12 \ |
| Product color | Black |
| Speaker enclosure | Closed |
| Power source type | AC |
| AC input frequency | 50 - 60 Hz |
| XLR in | Yes |
| Package weight | 26500 g |
| Certification | CE |
Weight and Dimensions| Subwoofer depth | 457.2 mm |
|---|---|
| Subwoofer width | 444.5 mm |
| Subwoofer height | 400 mm |
| Subwoofer weight | 20900 g |
Provides critical warnings and guidelines to prevent fire or electric shock.
Outlines precautions for outdoor use, temperature limits, and hearing protection.
Provides instructions and safety warnings for suspending ZXA1 loudspeakers.
Details controls for ZXA1: MASTER, MIC, MIC IN, LINE IN, WITH SUB/FULL RANGE, MASTER OUT, POWER.
Troubleshooting steps for when the amplifier or wiring produces no sound output.
Solutions for intermittent output, cracking, or distortion, possibly due to cables.
Diagnoses and resolves constant noise issues like buzzing, hissing, or humming.
Troubleshoots distorted sound and persistent LIMIT LED indication.
To Next Page
