What to do if I detect a leak in my ELGA Laboratory Equipment?
If you detect a leak, immediately press the mute button to silence the alarm. Then, remove the power, rectify the leak, and dry the sensors. Ensure you also dry the contacts, and finally, power the system back on to reset.
What to do if the break tank is low in my ELGA Laboratory Equipment?
If the break tank is low, start by pressing the mute button to silence the alarm. Next, confirm the pressure and flow of the potable supply. If the problem continues, you may need to contact a local service provider.
How to resolve a water temperature alarm on my ELGA Laboratory Equipment?
If you receive a water temperature alarm, begin by pressing the mute button to silence the alarm. Next, confirm that the water temperature is suitable for your application. You may need to adjust the alarm setpoint or direct water to drain to introduce cool water.
What should I do about the permeate temperature alarm on my ELGA MEDICA Pro 30 Laboratory Equipment?
If the permeate temperature alarm is triggered, first press the mute button to silence the alarm. Then, confirm that the temperature is suitable for your application. You might need to adjust the alarm setpoint or confirm the potable supply temperature is suitable.
What to do if I have problems with reservoir level controls in my ELGA Laboratory Equipment?
If you are experiencing issues with the reservoir level controls, start by pressing the mute button to silence the alarm. Then, remove the power from the unit. If the problem persists after these steps, it is recommended to contact Technical Support.
What to do if I get a permeate purity alarm on my ELGA MEDICA Pro 30?
If you receive a permeate purity alarm, first press mute to silence the alarm. Then, confirm the displayed purity is suitable for the application. If issues persist, adjust the alarm setpoint or contact your local service provider.
What to do if there is high loop pressure in my ELGA MEDICA Pro 30 Laboratory Equipment?
If there is high loop pressure, first press the mute button to silence the alarm. Then, remove the power. If the issue continues, contact Technical Support for further assistance.
What to do if Protek L1 is incorrectly installed in my ELGA MEDICA Pro 30?
If the Protek L1 is incorrectly installed, first press the mute button to silence the alarm. Then, confirm that the Protek is correctly installed. Finally, power the system off and on to reset.
What should I do if the Medpure L1 is incorrectly installed in my ELGA MEDICA Pro 30 Laboratory Equipment?
If the Medpure L1 is incorrectly installed, first press the mute button to silence the alarm. Then, confirm that the Medpure L1 is correctly installed. Finally, power the system off and on to reset.
What to do when the UV lamp fails in my ELGA MEDICA Pro 30?
If the UV lamp fails, first press the mute button to silence the alarm. Then, change the lamp at the next available opportunity.
Important safety warnings and cautions for operating the MEDICA unit.
Essential safety information regarding electrical supply isolation and earthing.
Procedure for isolating and releasing residual pressure before maintenance.
Guidance on unit installation, recommending trained ELGA representative.
Information on the commissioning mode and recommending trained ELGA representative.
Details on Master, User, and Sanitization keys for system access.
Deleting or adding User keys for access control.
Adding or deleting Sanitization Keys required to start sanitization.
Procedure for replacing the Composite Vent Filter.
Procedure for replacing the Medpure L1 cartridge.
Procedure for replacing the Ultra-Microfilter.
Procedure for replacing the UV lamp.
Procedure for replacing Protek L1/L2 pre-treatment cartridges.
Procedure for replacing the E-Cartridge on RE variants.
Procedure for sanitizing the RO module to reduce microbiological contamination.
Steps to initiate the RO sanitization process.
Confirming that the sanitant has been added to the system.
Detailed steps for the RO sanitization process.
Procedure for emergency bypass on MEDICA R/RE/RX models.
Procedure for emergency bypass on MEDICA B/S/SE models.
General| Brand | ELGA |
|---|---|
| Model | MEDICA Pro 30 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page