What to do if I detect a leak in my ELGA Laboratory Equipment?
If you detect a leak, immediately press the mute button to silence the alarm. Then, remove the power, rectify the leak, and dry the sensors. Ensure you also dry the contacts, and finally, power the system back on to reset.
What to do if the break tank is low in my ELGA MEDICA Pro 60 Laboratory Equipment?
If the break tank is low, start by pressing the mute button to silence the alarm. Next, confirm the pressure and flow of the potable supply. If the problem continues, you may need to contact a local service provider.
How to resolve a water temperature alarm on my ELGA Laboratory Equipment?
If you receive a water temperature alarm, begin by pressing the mute button to silence the alarm. Next, confirm that the water temperature is suitable for your application. You may need to adjust the alarm setpoint or direct water to drain to introduce cool water.
What should I do about the permeate temperature alarm on my ELGA MEDICA Pro 60?
If the permeate temperature alarm is triggered, first press the mute button to silence the alarm. Then, confirm that the temperature is suitable for your application. You might need to adjust the alarm setpoint or confirm the potable supply temperature is suitable.
What to do if I have problems with reservoir level controls in my ELGA MEDICA Pro 60?
If you are experiencing issues with the reservoir level controls, start by pressing the mute button to silence the alarm. Then, remove the power from the unit. If the problem persists after these steps, it is recommended to contact Technical Support.
What to do if I get a permeate purity alarm on my ELGA Laboratory Equipment?
If you receive a permeate purity alarm, first press mute to silence the alarm. Then, confirm the displayed purity is suitable for the application. If issues persist, adjust the alarm setpoint or contact your local service provider.
What to do if there is high loop pressure in my ELGA MEDICA Pro 60 Laboratory Equipment?
If there is high loop pressure, first press the mute button to silence the alarm. Then, remove the power. If the issue continues, contact Technical Support for further assistance.
What to do if Protek L1 is incorrectly installed in my ELGA MEDICA Pro 60 Laboratory Equipment?
If the Protek L1 is incorrectly installed, first press the mute button to silence the alarm. Then, confirm that the Protek is correctly installed. Finally, power the system off and on to reset.
What should I do if the Medpure L1 is incorrectly installed in my ELGA MEDICA Pro 60?
If the Medpure L1 is incorrectly installed, first press the mute button to silence the alarm. Then, confirm that the Medpure L1 is correctly installed. Finally, power the system off and on to reset.
What to do when the UV lamp fails in my ELGA MEDICA Pro 60?
If the UV lamp fails, first press the mute button to silence the alarm. Then, change the lamp at the next available opportunity.
Crucial safety warnings and cautions for operating the equipment.
Guidance on the physical installation of the unit.
Steps to set up and configure the unit after installation.
How to set up reminders for replacing consumables.
Procedure for replacing the Composite Vent Filter.
Detailed steps for sanitizing the RO module using Minncare.
Identifies common alarms and recommended actions for troubleshooting.
General| Product Water Flow Rate | Up to 60 L/h |
|---|---|
| Endotoxin Specification | <0.001 EU/mL |
| Resistivity | 18.2 MΩ·cm |
| Total Organic Carbon (TOC) | <5 ppb |
| Particles >0.2 μm | <1/mL |
| Installation | Bench-top |
| Type | Water Purification System |
| Maximum Output Flow Rate | 60 L/h |
| Feed Water Requirements | Potable tap water |
| Display | LCD |
| Bacterial Specification | <0.1 CFU/mL |
| Output Water Quality | Type I |
| Weight | 45 kg |
| Power Supply | 100-240 V AC, 50-60 Hz |
| Applications | Clinical analyzers, cell culture, HPLC |
To Next Page