ELGO Electronic Z16 Series - User Manual

Details on the content and purpose of the operation manual.

Explains warning symbols like DANGER, CAUTION, ATTENTION used in the manual.

Outlines the warranty conditions and guarantee period for the product.

Provides helpful hints and recommendations for efficient and failure-free operation.

Steps to follow before disassembling the device, including power disconnection.

Guidelines for recycling and proper disposal of electronic waste components.

Overview of safety aspects to ensure optimal employee protection and potential hazardous situations.

Specifies required protective clothing and gloves for installation and operation.

Warns about dangers and potential liabilities arising from unintended or improper use of the device.

Safety advice for handling packages during transport, unpacking, and loading.

Instructions for examining deliveries for completeness and transport damages, and filing claims.

Specifies the required environmental conditions for storing the device, including temperature and humidity.

Describes the Z16 system components: magnetic sensor, indicator, and magnetic band.

Highlights the sensor head's resistance to dust, dirt, water, and general wear.

Details the indicator's programming possibilities, display, and battery life.

Provides dimensional drawings and measurements for the Z16 indicator unit.

Shows dimensional drawings and measurements for the magnetic sensor.

Describes the mounting angle (MW Z16) for attaching the indicator, allowing adjustability.

Details the aluminum guide rail and rubber guide carriage for mounting the sensor and display.

Lists technical specifications for the Z16 indicator, including display, power, and housing.

Details technical specifications for the MS20.25 magnetic sensor, including cable length and resolution.

Provides technical specifications for the magnetic tape, including operation temperature and accuracy.

Emphasizes that maintenance and installation work must be done by qualified personnel to prevent injury.

Explains the sensor's internal structure and the critical distance requirement between sensor and tape.

Illustrates the layout of the LCD display, identifying key indicators like battery status and value.

Details how to activate parameter levels and navigate through settings using the buttons.

Explains how to select specific digits (decades) on the display for modification.

Describes how to increment or decrement the value of the selected decade.

Instructions on how to exit the parameter setting mode and save changes.

Lists all available parameters (P01-P99) with their descriptions and default values.

Step-by-step guide on how to calibrate the sensor using the magnetic tape and the 'F' button.

Instructions for resetting all parameters to their default values and initiating calibration.

Explains how to set the current actual value as the reference value using 'F' and 'Set' buttons.

Describes how to toggle between incremental and absolute measurement modes using the 'incr/abs' button.

Details the components and construction of the magnetic tape accessory.

Warns about risks of injury during fault clearance and emphasizes using qualified personnel.

Advises on optimal installation locations to avoid interference from electrical fields.

Provides specific measures for suppressing electrical interference, like using RC elements and filters.

Outlines the steps to follow after clearing a fault, including resetting and checking the area.

Lists basic rules for assembly, wiring, and operating to ensure EMC compliance.

States that the unit itself is designed to be maintenance-free.

Explains the structure of the Z16 type designation codes for series, SN, supply, and options.

Details the coding system for the magnetic tape accessory, including series, pole pitching, and width.

An alphabetical index of terms and their corresponding page numbers for quick reference.

Details on the content and purpose of the operation manual.

Explains warning symbols like DANGER, CAUTION, ATTENTION used in the manual.

Outlines the warranty conditions and guarantee period for the product.

Provides helpful hints and recommendations for efficient and failure-free operation.

Steps to follow before disassembling the device, including power disconnection.

Guidelines for recycling and proper disposal of electronic waste components.

Overview of safety aspects to ensure optimal employee protection and potential hazardous situations.

Specifies required protective clothing and gloves for installation and operation.

Warns about dangers and potential liabilities arising from unintended or improper use of the device.

Safety advice for handling packages during transport, unpacking, and loading.

Instructions for examining deliveries for completeness and transport damages, and filing claims.

Specifies the required environmental conditions for storing the device, including temperature and humidity.

Describes the Z16 system components: magnetic sensor, indicator, and magnetic band.

Highlights the sensor head's resistance to dust, dirt, water, and general wear.

Details the indicator's programming possibilities, display, and battery life.

Provides dimensional drawings and measurements for the Z16 indicator unit.

Shows dimensional drawings and measurements for the magnetic sensor.

Describes the mounting angle (MW Z16) for attaching the indicator, allowing adjustability.

Details the aluminum guide rail and rubber guide carriage for mounting the sensor and display.

Lists technical specifications for the Z16 indicator, including display, power, and housing.

Details technical specifications for the MS20.25 magnetic sensor, including cable length and resolution.

Provides technical specifications for the magnetic tape, including operation temperature and accuracy.

Emphasizes that maintenance and installation work must be done by qualified personnel to prevent injury.

Explains the sensor's internal structure and the critical distance requirement between sensor and tape.

Illustrates the layout of the LCD display, identifying key indicators like battery status and value.

Details how to activate parameter levels and navigate through settings using the buttons.

Explains how to select specific digits (decades) on the display for modification.

Describes how to increment or decrement the value of the selected decade.

Instructions on how to exit the parameter setting mode and save changes.

Lists all available parameters (P01-P99) with their descriptions and default values.

Step-by-step guide on how to calibrate the sensor using the magnetic tape and the 'F' button.

Instructions for resetting all parameters to their default values and initiating calibration.

Explains how to set the current actual value as the reference value using 'F' and 'Set' buttons.

Describes how to toggle between incremental and absolute measurement modes using the 'incr/abs' button.

Details the components and construction of the magnetic tape accessory.

Warns about risks of injury during fault clearance and emphasizes using qualified personnel.

Advises on optimal installation locations to avoid interference from electrical fields.

Provides specific measures for suppressing electrical interference, like using RC elements and filters.

Outlines the steps to follow after clearing a fault, including resetting and checking the area.

Lists basic rules for assembly, wiring, and operating to ensure EMC compliance.

States that the unit itself is designed to be maintenance-free.

Explains the structure of the Z16 type designation codes for series, SN, supply, and options.

Details the coding system for the magnetic tape accessory, including series, pole pitching, and width.

An alphabetical index of terms and their corresponding page numbers for quick reference.