EasyManuals Logo

Eliwell IDplus 902 User Manual

Eliwell IDplus 902
44 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #28 background imageLoading...
Page #28 background image
PAR. DESCRIPTION RANGE App1 App2 App3 App4 M.U.
COMMUNICATION (“Addfolder)
PtS Communication protocol selection. t = Televis; d = Modbus. t/d t t t t flag
dEA Index of the device inside the family (valid values from 0 to 14). 0 ... 14 0 0 0 0 num
FAA Device family - valid values from 0 to 14. 0 ... 14 0 0 0 0 num
Pty Modbus parity bit. n = none; E = even; o = odd. n/E/o n n n n num
StP Modbus stop bit. 1b/2b 1b 1b 1b 1b flag
DISPLAY (‘diS’ folder)
LOC
Basic commands modification lock. It is still possible to enter parameter programming
mode and modify them. y = yes; n = no.
n/y
n n n n
flag
PS1 PAssword1: if PS1≠0 is the access key to "User" parameters. 0 ... 250 0 0 0 0 num
PS2 PAssword2: if PS2≠0 is the access key to "Installer" parameters. 0 ... 250 15 15 15 15 num
ndt Display with decimal point. y = yes; n = no. n/y y y y y flag
CA1 Calibration 1. Temperature value to be added to the Pb1 value. -12,0...12,0 0,0 0,0 0,0 0,0 °C/°F
CA3 Calibration 3. Temperature value to be added to the Pb3 value. -12,0...12,0 0,0 0,0 0,0 0,0 °C/°F
ddL
Display mode during defrost.
0= display temperature recorded by Pb1;
1= lock recorded Pb1 value at the start of the defrost cycle; 2= display the “dEF” label.
0/1/2 0 0 0 0 num
Ldd Timeout value for display unlock - dEF label 0 ... 255 30 30 30 30 min
dro
Select the unit of measurement used when displaying the temperature recorded by the
probes. (0 = °C, 1 = °F).
NOTE: switching between °C and °F or vice-versa DOES NOT modify the SEt,
diF values, etc. (e.g. Setpoint=10°C becomes 1F)
0/1 0 0 0 0 flag
ddd
Selects type of value to display.
0 = Setpoint; 1 = probe Pb1; 2 = probe Pb2; 3 = probe Pb3
0/1/2/3 1 1 1 1 num
HACCP (“HCP” folder)
SHH Maximum HACCP alarm signals threshold. -55,0...150
0,0 0,0 0,0 0,0
°C/°F
SLH Minimum HACCP alarm signals threshold. -55,0...150 0,0 0,0 0,0 0,0 °C/°F
drA
Minimum time spent in critical range for the event to be recorded. After this a HACCP
alarm will be triggered and logged.
0 ... 99 0 0 0 0 min
drH HACCP alarm reset time after last reset. 0 ... 250 0 0 0 0 hours

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Eliwell IDplus 902 and is the answer not in the manual?

Eliwell IDplus 902 Specifications

General IconGeneral
BrandEliwell
ModelIDplus 902
CategoryController
LanguageEnglish

Related product manuals