Emerson Dixell XWi70K - Parameter List (LT Configuration - Part 3); Parameter List (NT Configuration - Part 3)

1592026601 XWi70K STD FULL EN r1.6 2022.07.29.docx XWi70K 13/15
dAF_nt
Pre-defrost time
0
Pr1
min
od1_nt
Automatic defrost (at the beginning of any energy
saving)
no
Pr2
od2_nt
Optimized defrost
no
Pr2
Syd_nt
Tipe of synchronized defrost
nU
Pr2
dt1_nt
Differential temperature for latent heating control
0,2
Pr2
°C
ndE_nt
Number of connected controllers for random refrost
(Syd=rnd)
1
Pr2
FAP_nt
Probe selection for evaporator fan
nP
Pr1
FSt_nt
Evaporator fan stop temperature
20.0
Pr1
°C
HyF_nt
Evaporator fan regulator differential
5.0
Pr1
°C
FnC_nt
Evaporator fan operating mode
C_n
Pr1
Fnd_nt
Evaporator fan delay after defrost cycle
1
Pr1
min
FCt_nt
Differential temperature for cyclic activation of
evaporator fans (0=disabled)
0
Pr1
°C
Fon_nt
Evaporator fan ON time in normal mode (with
compressor OFF)
1
Pr2
min
FoF_nt
Evaporator fan OFF time in normal mode (with
compressor OFF)
1
Pr2
min
LA1_nt
Maintenance interval for evaporator fans (tens of
hours)
0
Pr2
hour *100
rS1_nt
Maintenance function reset
no
Pr2
FAC_nt
Probe selection for condenser fan
nP
Pr2
St2_nt
Set Point 2 Regulation (for condenser fan)
15.0
Pr2
°C
Hy2_nt
Set Point 2 differential (for condenser fan)
20.0
Pr2
°C
FCC_nt
Condenser fan operating mode
C_n
Pr1
FCo_nt
Condenser fan deactivation delay
20
Pr1
sec
LA2_nt
Condenser fan working hours (x100) for
maintenance alarm
0
Pr2
hour *100
rS2_nt
Condenser fan maintenance alarm reset
no
Pr2
CMi_nt
Minimum speed for condenser fan
20
Pr2
%
CMA_nt
Maximum speed for condenser fan
100
Pr2
%
CSS_nt
Safety speed for condenser fan
80
Pr2
%
ACH_nt
Type of control for auxiliary regulator
CL
Pr1
SAA_nt
Set point for auxiliary regulator
0.0
Pr1
°C
SHy_nt
Auxiliary regulator differential
5.0
Pr1
°C
ArP_nt
Probe selection for auxiliary regulator
nP
Pr1
Sdd_nt
Auxiliary regulator disabled during any defrost
cycle
yes
Pr1
btA_nt
Base time for parameters Ato and AtF
Min
Pr1
Ato_nt
Interval of time with auxiliary output ON
0
Pr1
min
AtF_nt
Interval of time with auxiliary output OFF
0
Pr1
min
1An_nt
Type of analogue output 1
Vlt
Pr1
1oL_nt
Minimum value for analogue output 1
5
Pr1
%
1oH_nt
Maximum value for analogue output 1
100
Pr1
%
1At_nt
Interval of time with analogue output 1 (maximum
value)
5
Pr1
sec
2An_nt
Type of analogue output 2
Vlt
Pr1
2oL_nt
Minimum value for analogue output 2
5
Pr1
%
2oH_nt
Maximum value for analogue output 2
100
Pr1
%
2At_nt
Interval of time with analogue output 2 (maximum
value)
5
Pr1
sec
ALP_nt
Probe selection for temperature alarms
nP
Pr1
ALC_nt
Temperature alarms configuration: relative,
absolute
Ab
Pr1
ALU_nt
High temperature alarm
150.0
Pr1
°C
ALL_nt
Low temperature alarm
-100.0
Pr1
°C
AFH_nt
Temperature alarm differential
5.0
Pr2
°C
ALd_nt
Temperature alarm delay
0
Pr1
min
dot_nt
Temperature alarm delay with open door
0
Pr1
min
dAo_nt
Temperature alarm delay at start-up
00:00
Pr1
hour
AP2_nt
Probe selection for 2nd temperature alarm
nP
Pr2
AL2_nt
2nd low temperature alarm
100.0
Pr2
°C
AU2_nt
2nd high temperature alarm
5.0
Pr2
°C
AH2_nt
2nd temperature alarm differential
5.0
Pr2
°C
Ad2_nt
2nd temperature alarm delay
0
Pr2
min
dA2_nt
2nd temperature alarm delay at start-up
00:00
Pr2
hour
dE2_nt
Temperature alarm 2 disabled during every defrost
and dripping phase
nU
Pr2
bLL_nt
Compressor OFF due to 2nd low temperature
alarm
no
Pr2
AC2_nt
Compressor OFF due to 2nd high temperature
alarm
no
Pr2
SAF_nt
Differential for anti-freezing control
3.0
Pr1
°C
tbA_nt
Alarm relay deactivation
yes
Pr1
bUM_nt
Buzzer muting
no
Pr1
oA1_nt
Relay output oA1 configuration
FAn
Pr2
oA2_nt
Relay output oA2 configuration
Cnd
Pr2
oA3_nt
Relay output oA3 configuration
LiG
Pr2
oA4_nt
Relay output oA4 configuration
dEF
Pr2
oA5_nt
Relay output oA5 configuration
ALr
Pr2
1Ao_nt
Analogue output 1 configuration
nU
Pr2
2Ao_nt
Analogue output 2 configuration
nU
Pr2
3Ao_nt
Analogue output 3 configuration
nU
Pr2
AoP_nt
Alarm relay polarity
CL
Pr1
i1P_nt
Digital input 1 polarity
CL
Pr1
i1F_nt
Digital input 1 configuration
EAL
Pr1
did_nt
Digital inputs 1 alarm delay (base time depends on
par. ibt)
0
Pr1
min
i2P_nt
Digital input 2 polarity
CL
Pr1
i2F_nt
Digital input 2 configuration
dor
Pr1
d2d_nt
Digital inputs 2 alarm delay (base time depends on
par. ibt)
0
Pr1
min
nPS_nt
Number of external pressure switch alarms before
stopping the regulation
0
Pr2
odC_nt
Compressor and fan status after door opening
F-C
Pr2
rrd_nt
Regulation restart after door alarm
yes
Pr2
HES_nt
Temperature differential in energy saving
1
Pr1
°C
ESt_nt
Energy saving timeout
0
Pr1
hour