DVC6000 Digital Valve Controllers
i
Fast Key Sequence for Instrument Level HC, AD, PD, and ODV
Function/Variable
Fast-Key
Sequence
Coordinates
(1)
Function/Variable
Fast-Key
Sequence
Coordinates
(1)
A Minus B 3-5-3 4-G End Point Pressure Control
(3)
1-2-2-2-4 8-D
Actuator Style 1-2-6-4 3-D
Failure Group Enable
1-2-3-6-5-1
11-I
Alert Conditions 2-1 2-F 1-2-3-7-5-1
Alert Record Full Enable
1-2-3-6-2
10-H
Firmware Revision 3-7-6 2-H
1-2-3-7-2 Flash ROM Shutdown 1-2-3-1-3-5 12-C
Alert Record Has Entries Enable
1-2-3-6-1
10-H
Hardware Revision 3-7-7 2-H
1-2-3-7-1
HART Tag
1-2-5-1-1 6-F
Analog Input 3-1 2-G 3-7-1 2-H
Analog Input Calibration 1-3-2-3 4-E HART Universal Revision 3-7-9 2-H
Analog Input Range Hi 1-2-5-3-1 6-H Input Characterization 1-2-2-3 4-C
Analog Input Range Lo 1-2-5-3-2 6-H
Instrument Date and Time
1-2-4-1-2 8-G
Analog Input Units 1-2-5-2-3 6-G 1-2-5-8 4-G
Auto Calibration 1-3-1-1 4-E Instrument Level 3-7-8 2-H
Autocalibration in Progress Enable 1-2-4-2-2 8-H
Instrument Mode
Hot Key-1 1-A
Auxiliary Input
3-6-1 4-H 1-2-1-1 4-B
1-2-3-3-1-2 12-D Instrument Serial Number 1-2-5-1-6 6-G
Auxiliary Terminal Action
1-2-3-3-1-3 12-E Instrument Time Invalid Enable 1-2-4-1-1 8-G
1-2-5-7 4-G
Integral Dead Zone
1-2-4-4-4 8-I
Auxiliary Terminal Alert Enable 1-2-3-3-1-1 12-E 1-2-2-1-2-1 8-B
Burst Command 1-2-1-4-3 6-B Integral Enable (Travel Tuning) 1-2-2-1-1-2 8-A
Burst Enable 1-2-1-4-1 6-B Integral Enable (Pressure Tuning) 1-2-2-1-3-2 8-C
Calibration in Progress Enable 1-2-4-2-1 8-G Integral Gain (Travel Tuning) 1-2-2-1-1-3 8-A
Clear ALL Records
1-2-3-6-4
10-H
Integral Gain (Pressure Tuning) 1-2-2-1-3-3 8-C
1-2-3-7-4
Integral Limit
1-2-4-4-3 8-I
Command 3 Configured Pressure 1-2-1-4-5 6−B 1-2-2-1-2-2 8-B
Control Mode
Hot Key-2 1-A Integrator Saturated Hi Enable 1-2-4-4-1 8-I
1-2-1-2 4-B Integrator Saturated Lo Enable 1-2-4-4-2 8-I
Critical NVM Shutdown 1-2-3-1-3-4 12-C Last AutoCalibration Status 1-2-5-9-1 6-H
Custom Characterization Table 1-2-2-4 4-C Last Calibration Type 1-2-5-9-2 6-H
Cutoff Hi
1-2-3-4-7-3 12-G Loop Current Validation Enable
(6)
1-2-3-3-3 9-E
1-2-2-2-2-1 10-B Low Power Write Fail Enable
(6)
1-2-3-1-3-2 12-B
Cutoff Lo
1-2-3-4-7-4 12-G Manual Calibration 1-3-1-2 4-E
1-2-2-2-2-2 10-B Manufacturer (Actuator) 1-2-6-1 3-D
Cycle Counter
1-2-3-5-1-2 12-H Manufacturer (Instrument) 3-7-3 2-H
3-6-5 4-H
Maximum Recorded Temperature
3-6-3 4-H
Cycle Counter Alert Enable 1-2-3-5-1-1 12-G 2-3-1 3-F
Cycle Count Alert Point 1-2-3-5-1-3 12-H Maximum Supply Pressure 1-2-5-6 4-G
Date 1-2-5-1-4 6-G Message 1-2-5-1-2 6-F
Dead Band (Cycle Count / Travel
Accumulator)
1-2-3-5-2-1 12-H
Minimum Recorded Temperature
2-3-2 3-F
Descriptor 1-2-5-1-3 6-F 3-6-4 4-H
Device Description Information 3-8 2-G
Miscellaneous Group Enable
1-2-3-6-5-3
11-I
Device ID 3-7-2 2-H 1-2-3-7-5-3
Device Revision 3-7-5 2-H Model (Device) 3-7-4 2-H
Diagnostic Data Available Enable 1-2-4-2-4 8-H Multi-Drop Alert Enable 1-2-4-3-2 8-H
Diagnostic in Progress Enable 1-2-4-2-3 8-H No Free Time Shutdown 1-2-3-1-3-6 12-C
Drive Current Shutdown 1-2-3-1-1 8-D Non-Critical NVM Alert Enable 1-2-3-1-3-3 12-C
Drive Signal Alert Enable 1-2-3-1-2-1 10-D
Number of Power Ups
2-3-4 3-G
Drive Signal
3-4 2-G 3-6-9 4-H
1-2-3-1-2-2 10-D Offline/Failed Alert Enable 1-2-3-1-3-1 12-B
NOTE: Italicized Fast-Key Sequence indicates fast-key sequence is applicable only for instrument level ODV.
1. Coordinates are to help locate the item on the menu tree on the following pages.
3. Instrument level ODV only.
5. Instrument level HC, AD, and PD only.
6. Firmware 9 and 10 only.
To Next Page
Loading...
Need help?
General
