What to do if Emerson Liebert GXT shuts down automatically due to overload?
If the Emerson UPS shuts down automatically due to overload times exceeding the specification, remove some of the connected devices to reduce the load on the UPS. Then, restart the UPS.
What to do if Emerson UPS is locked in bypass after overload?
If your Emerson UPS is locked in bypass after experiencing three overloads within 30 minutes, begin by removing excess loads from the UPS output. After doing so, shut down the UPS and then restart it.
What to do if EPO plug is removed on Emerson UPS?
To fix this problem, connect the EPO plug (jumper) securely or switch on the external EPO switch of your Emerson UPS.
How to fix a blocked fan in Emerson Liebert GXT?
If the fan in your Emerson UPS is blocked, clean the fan to ensure it is not obstructed.
What to do if battery protection device is open in Emerson Liebert GXT UPS?
If the battery protection device in your Emerson UPS is open, replace or restore the protection device.
What to do if Emerson Liebert GXT UPS battery is deeply discharged?
To resolve a deeply discharged battery in your Emerson UPS, recharge the battery.
What to do if parallel communication cable is loosen in Emerson Liebert GXT UPS?
If the parallel communication cable is loose or the parallel operation is incorrect in your Emerson UPS, ensure the parallel communication cable is tightly connected. Also, check if the 'parallel information' in the LCD is ok. Then, turn on UPS after removing the warning message by pressing the ‘UP’ and ‘DOWN’ buttons together. If you have a single UPS without communication cables connected, you can ignore this warning message and remove it by pressing the ‘UP’ and ‘DOWN’ buttons, then turn on the UPS.
What to do if cover of maintain switch is open in Emerson Liebert GXT?
If the cover of the maintain switch is open on your Emerson UPS, put the cover back in place.
What to do if input fuse is blown in Emerson Liebert GXT UPS?
If the input fuse on the power stage board of your Emerson UPS is blown, check and replace the input fuse.
What to do if charger voltage is too high on Emerson Liebert GXT?
If the charger voltage is too high on your Emerson UPS, disconnect the battery and check the charger output voltage. Then, contact the dealer for repair.
Instructions for safely moving and storing the UPS unit.
Precautions before installing the UPS, including acclimation and environmental checks.
Guidelines for installing the UPS, including load limits, ventilation, and earthing.
Safety considerations during UPS operation, including earth connection and power disconnection.
Lists safety and EMC standards the UPS complies with, such as IEC/EN 62040.
Steps for unpacking the UPS and checking package contents for damage.
Identifies various ports and components on the rear panel of the UPS.
Illustrates rear panels and input/output terminals for tower and rack models.
Detailed steps and wiring specifications for installing a single UPS unit.
Instructions for installing multiple UPS units in a parallel system.
Instructions for installing monitoring software for UPS management and shutdown.
Explains the function of each button on the UPS front panel.
Describes the front panel LED indicators and the LCD panel layout.
Details the various display screens and information shown on the UPS LCD panel.
Lists the different audible alarms, their causes, and whether they can be muted.
Step-by-step guide on how to turn on and operate a single UPS unit.
Explains how the UPS operates when using battery power, including alarms and backup time.
Instructions on how to perform a battery self-test and its periodic nature.
Procedure for safely turning off the UPS when connected to utility power.
Procedure for safely turning off the UPS when running on battery power.
How to mute the UPS audible alarms.
How to interpret and address warning indicators and codes.
How to interpret and address critical fault conditions and errors.
Procedure for qualified technicians to change battery configuration.
Instructions for connecting and operating multiple UPS units in parallel.
Steps for connecting UPS units in a parallel system and verifying connections.
Procedure for adding a new UPS unit to an existing parallel system.
Procedure for safely removing a UPS unit from a parallel system.
Explains common abbreviations displayed on the UPS LCD screen.
Shows the UPS LCD interface for single and parallel models, detailing parameters.
Details the UPS parameter settings via the LCD interface.
Setting to enable or disable the frequency converter function.
Setting for output frequency, including auto and fixed modes.
Setting to enable or disable the ECO (Energy Saving) mode.
Configuration to allow or forbid the UPS from operating in bypass mode.
Setting to enable or disable manual operation of bypass mode.
Setting the maximum backup time and battery discharge protection.
Setting to enable or disable the hot standby function.
Configuration for programmable output, including ON, OFF, and ATO modes.
Setting the shutdown voltage for programmable output.
Setting the shutdown time for programmable output.
Describes the UPS operation in AC mode and its LCD display.
Describes the UPS operation in ECO mode and its LCD display.
Describes the UPS operation in CVCF mode and its LCD display.
Describes the UPS operation in Battery mode and its LCD display.
Describes the UPS operation during battery test and its LCD display.
Describes the UPS operation in bypass mode and its LCD display.
Describes how fault status is displayed on the UPS LCD panel.
Lists fault codes, their icons, events, and possible causes.
Lists warning codes, icons, descriptions, and alarm sounds.
Troubleshooting table for warning conditions, including cause and remedy.
Troubleshooting table for fault conditions, including cause and remedy.
Guidelines for storing the UPS, including charging frequency and duration.
Safety precautions and general guidelines for maintaining the UPS system.
To Next Page
General