Emerson Liebert GXT3 Series

Questions and Answers

L
lisa28Jul 26, 2025
Why does my Emerson UPS have reduced battery backup time?
- G
  George QuinnJul 26, 2025
  If your Emerson UPS has reduced battery backup time, it could be due to several reasons. First, the batteries might not be fully charged. To resolve this, keep the UPS plugged in continuously for at least 24 hours to recharge them. Second, the UPS could be overloaded. Check the load level indicator and reduce the load on the UPS. Finally, the batteries may not be able to hold a full charge due to age. In this case, replace the batteries.
S
Steve ReidAug 2, 2025
Why is the battery indicator illuminated on my Emerson Liebert GXT3?
- K
  Katherine SmithAug 2, 2025
  If the battery indicator is illuminated on your Emerson UPS, it could mean a few things. First, the UPS might not be plugged in, so ensure it is securely plugged into the wall receptacle and is operating from battery mode. Second, the UPS input protection fuse may have blown or opened, causing it to operate from battery mode; in this case, save your data, close applications, replace the UPS input fuse, and then restart the UPS. Third, the utility power might be out of tolerance, also causing the UPS to operate from battery mode; save your data, close applications, and ensure the utility supply voltage is within acceptable limits for the UPS.
J
Jillian DavisAug 8, 2025
What to do if Fault and Bypass indicators and all LED segments of battery level indicator are illuminated on Emerson Liebert GXT3 UPS?
- E
  Erica WashingtonAug 8, 2025
  If the Fault and Bypass indicators along with all LED segments of the battery level indicator are illuminated on your Emerson UPS, it indicates that the UPS is overloaded or the load is faulty. Check the load level indicator and remove non-essential loads. Recalculate the load and reduce the number of loads connected to the UPS. Also, check the connected loads for faults.
R
Rebecca HolmesAug 13, 2025
What does it mean when Fault and Bypass indicators and diagnostic A indicator are illuminated on Emerson UPS?
- S
  Sarah RuizAug 13, 2025
  If the Fault and Bypass indicators and diagnostic A indicator are illuminated on your Emerson UPS, it means the UPS shut down due to a temperature condition, and the load is on bypass power. Make sure the UPS is not overloaded, that the ventilation holes are not blocked, and that the room ambient temperature is not excessive. Wait 30 minutes to allow the UPS to cool down, then restart it.
A
Amy GarciaAug 19, 2025
What to do if Emerson UPS fails to start when the On/Alarm Silence/Manual Battery Test button is pressed?
- H
  hoovermitchellAug 19, 2025
  If your Emerson UPS fails to start when you press the On/Alarm Silence/Manual Battery Test button, it could be short-circuited or overloaded. Ensure the UPS is off, disconnect all loads, and make sure nothing is lodged in the output receptacles. Also, ensure that the loads are not defective or shorted internally.

Summary

Important Safety Precautions

Safety Instructions

Save these instructions for future reference regarding UPS and battery safety.

Glossary of Symbols

Product Description

Features

Key features of the Liebert GXT3 UPS system.

Available Models

Lists the different UPS models available.

Appearance and Components Overview

Overview of the UPS front and rear panel features and components.

Major Components

Detailed explanation of the UPS's major internal components.

UPS Operating Modes

Describes different operational states like Utility, Battery, Bypass, and Converter modes.

Installation

Unpacking and Inspection

Steps for unpacking and inspecting the UPS unit.

Whats Included

Lists all accessories and components included with the UPS.

Installation Preparation

Guidelines for preparing the environment for UPS installation.

Mechanical Installation Methods

Instructions for installing the UPS in tower or rack configurations.

Power Cable Connections

Connecting input power plug, loads, and battery cables.

Communication Cable Connections

Connecting USB and optional IntelliSlot communication cables.

Controls and Indicators

Control Buttons

Details on the function of the UPS control buttons.

UPS Indicators and Status

Explanation of battery level and status indicators on the UPS.

Operation

Startup Checklist

Pre-startup checks for the Liebert GXT3 UPS.

Starting the UPS

Step-by-step instructions for starting the UPS.

Manual Battery Test

Procedure to perform a manual test of the UPS battery.

Manual Bypass

How to manually switch the UPS to bypass mode.

Shut Down the UPS

Procedure for safely shutting down the Liebert GXT3 UPS.

Disconnecting Input Power

Steps to disconnect the input power from the UPS.

Communication

IntelliSlot Communication Options

Details on optional IntelliSlot cards for network communication.

USB Port Configuration

Using the USB port for UPS configuration and software.

Terminal Block Communication

Using the terminal block for shutdown commands and status signals.

Maintenance

Internal Battery Replacement

Step-by-step guide for replacing the internal UPS battery pack.

Battery Charging

Information on how the UPS charges its batteries.

Precautions

General safety and maintenance precautions for the UPS.

Checking UPS Status

Procedures for checking the UPS operational status.

Checking UPS Functions

How to perform functional checks on the UPS.

Troubleshooting

Identifying UPS Symptoms

Understanding indicator lights and their relation to UPS problems.

Audible Alarm

Explanation of audible alarms and their meanings.

Troubleshooting Guide

Table of common UPS problems, causes, and solutions.

Battery Cabinet

Specifications

Product Warranty Registration

Instructions for registering the UPS for warranty protection.

Emerson Liebert GXT3 Series Specifications

General

Model	Liebert GXT3 Series
Frequency	50/60 Hz
Type	Online Double Conversion
Power Capacity	1kVA to 10kVA
Input Voltage	120V, 208V, 230V (depending on the specific model)
Output Voltage	120V, 208V, 230V (depending on the specific model)
Backup Time	Varies by model and load
Form Factor	Tower/Rackmount
Operating Temperature	0 to 40°C (32 to 104°F)
Humidity	0% to 95% (non-condensing)
Dimensions	Varies depending on the specific model
Weight	Varies by model
Battery Type	Valve-regulated lead acid (VRLA)