Endress+Hauser PROFIBUS PA

Questions and Answers

S
Stephen SharpSep 12, 2025
What does SIL lock device mean on Endress+Hauser PROFIBUS PA Measuring Instruments?
- C
  Caitlyn GonzalezSep 12, 2025
  If the Endress+Hauser Measuring Instruments display 'SIL lock device', it means that the SIL_locking process has not been completed.
J
John BarberAug 25, 2025
What to do if full/covered not calibrated on Endress+Hauser Measuring Instruments?
- C
  charles55Aug 25, 2025
  If Endress+Hauser Measuring Instruments are showing a 'full/covered not calibrated' message, perform a full/covered calibration using the calibration function group.
A
andrewsseanAug 25, 2025
What to do if empty/free not calibrated on Endress+Hauser Measuring Instruments?
- J
  Jason RodriguezAug 26, 2025
  If Endress+Hauser Measuring Instruments are showing a 'empty/free not calibrated' message, perform an empty/free calibration using the calibration function group.
S
sampsonchristopherSep 23, 2025
What to do if Endress+Hauser Measuring Instruments have download error?
- W
  williamaustinSep 23, 2025
  To resolve a 'Download error' on your Endress+Hauser Measuring Instruments, repeat the download process.
J
joyce21Sep 12, 2025
What to do if electronics defect on Endress+Hauser PROFIBUS PA?
- D
  Deborah WhiteSep 12, 2025
  If you are facing an 'electronics defect' error with your Endress+Hauser Measuring Instruments, try switching the instrument off and on.
J
Julia WilsonSep 18, 2025
How to fix 'Linearization table not defined' on Endress+Hauser PROFIBUS PA Measuring Instruments?
- M
  Mark MillerSep 18, 2025
  To resolve the 'Linearization table not defined' error on your Endress+Hauser Measuring Instruments, enter or complete the linearization table in the "linearization" (*4) function group. Ensure the table contains the endpoints 0% = 1000 cps (standardized) and 100% = 0 cps (standardized). When entering via FieldCare, select the correct table type (lin. tab. "level" or "concentration").
M
Michael GutierrezSep 5, 2025
What to do if Endress+Hauser Measuring Instruments show error W153?
- K
  Kevin ReeseSep 5, 2025
  If your Endress+Hauser Measuring Instruments display error W153, wait for completion of the initializing procedure.
M
moyermitchellSep 6, 2025
What to do if Endress+Hauser PROFIBUS PA Measuring Instruments show error A106?
- G
  Gary RodriguezSep 6, 2025
  If your Endress+Hauser Measuring Instruments display error A106, wait for completion of the download.
B
bradleypetersonSep 18, 2025
How to troubleshoot 'Linearization table not plausible' on Endress+Hauser PROFIBUS PA?
- J
  Joseph BlackwellSep 18, 2025
  To resolve the 'Linearization table not plausible' error on your Endress+Hauser Measuring Instruments, check the monotony of the linearization table and adjust it if necessary using the "linearization" (*4) function group.
K
katherineharringtonAug 30, 2025
What happens when Endress+Hauser Measuring Instruments issues a warning error?
- E
  Eric HoltAug 30, 2025
  When a warning error occurs, the Endress+Hauser Measuring Instruments device continues measurement, and an error message is displayed, alternating with the measured value.

Endress+Hauser PROFIBUS PA Specifications

General

Communication Protocol	PROFIBUS PA
Manufacturer	Endress+Hauser
Power supply	9-32 V DC (via PROFIBUS PA)
Protection class	IP67
Housing material	Stainless steel or plastic