Endress+Hauser PROFIBUS PA

Questions and Answers:

V
Veronica GreenAug 23, 2025
What to do if density not calibrated on Endress+Hauser Measuring Instruments?
- M
  millermaryAug 25, 2025
  To resolve a 'density not calibrated' error with Endress+Hauser Measuring Instruments: * Verify that at least one calibration point has been entered and activated within the calibration function group. If not, enter and activate the necessary calibration points. * Ensure that the reference pulse rate is not larger than 232. If it is, re-perform the density calibration within the calibration function group.
N
nicholsonanthonySep 1, 2025
What to do if Endress+Hauser Measuring Instruments show error A111?
- M
  matthewoliverSep 1, 2025
  If your Endress+Hauser Measuring Instruments display error A111 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
S
Shannon GonzalesSep 1, 2025
What to do if Endress+Hauser PROFIBUS PA Measuring Instruments show error A113?
- C
  Carolyn MasonSep 2, 2025
  If your Endress+Hauser Measuring Instruments display error A113 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
M
Michael GrahamSep 2, 2025
What to do if Endress+Hauser Measuring Instruments show error A114?
- H
  haileyedwardsSep 2, 2025
  If your Endress+Hauser Measuring Instruments display error A114 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
P
Paul GraySep 3, 2025
What to do if Endress+Hauser PROFIBUS PA show error A121?
- D
  David WalkerSep 3, 2025
  If your Endress+Hauser Measuring Instruments display error A121 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
J
Jose RuizSep 4, 2025
What to do if Endress+Hauser Measuring Instruments show error A116?
- C
  Christian JonesSep 4, 2025
  If your Endress+Hauser Measuring Instruments display error A116, repeat the download.
C
Christine HendersonSep 4, 2025
What to do if Endress+Hauser PROFIBUS PA Measuring Instruments show error W103?
- K
  Kelly DunnSep 4, 2025
  If your Endress+Hauser Measuring Instruments display error W103, wait for completion of the initializing procedure.
M
Michael GutierrezSep 5, 2025
What to do if Endress+Hauser Measuring Instruments show error W153?
- K
  Kevin ReeseSep 5, 2025
  If your Endress+Hauser Measuring Instruments display error W153, wait for completion of the initializing procedure.
M
moyermitchellSep 6, 2025
What to do if Endress+Hauser PROFIBUS PA Measuring Instruments show error A106?
- G
  Gary RodriguezSep 6, 2025
  If your Endress+Hauser Measuring Instruments display error A106, wait for completion of the download.
S
sarah93Sep 7, 2025
How to fix linearization table not plausible on Endress+Hauser PROFIBUS PA Measuring Instruments?
- P
  Paul CoxSep 7, 2025
  If the Endress+Hauser Measuring Instruments display 'linearization table not plausible', check the monotony of the linearization table. If necessary, adjust the table within the "linearization" function group.

Endress+Hauser PROFIBUS PA Specifications

General

Communication Protocol	PROFIBUS PA
Manufacturer	Endress+Hauser
Power supply	9-32 V DC (via PROFIBUS PA)
Protection class	IP67
Housing material	Stainless steel or plastic