Episode EA-AMP-HYB-2D-2000 Quick Start Guide

9 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

QUICK START GUIDE

EA-AMP-HYB-2D-1000

EA-AMP-HYB-2D-2000

EA-AMP-HYB-2D-1000

CH.SEL

PROTECT

CH2

ADJUST | SET

MENU

BACK

CLIP

-10

-20

SIGNAL

PROTECT

CH1

CLIP

-10

-20

SIGNAL

A

T

TENTION ! RISQUE DE CHOC ! ÉLECTRIQUE P

AS OUVRIR !

CAUTION

RISK OF ELECTRICAL SHOCK!

DO NOT OPEN!

!

Use only a 250V fuse

Employer uniquement aux

un fusible de 250V

U

C UL

LIFTED

ON

OFF

110 V FUSE T8AH 250V

230V FUSE T4A H250V

118V110-120V AC-60H-230W

230V230-240AC-50Hz-230W

SPEAKER OUT

BRIDGE

DIGITAL

IN

CH1

CH1

CH2

CH2

LINE OUT

CH1

CH1

CH2

CH2

IN

LINK ACT

OUT

LINE IN

TRIGGER

DC 12 V

SERIAL

CONTROL

NETWORK

CONTROL

OUT

CH2 CH1

L

Table of Contents

Other manuals for Episode EA-AMP-HYB-2D-2000

Product Manual20 pages

Questions and Answers:

D
David WeaverAug 9, 2025
Why is the Episode EA-AMP-HYB-2D-2000 Amplifier audio distorted at normal volume?
- S
  stoutgloriaAug 9, 2025
  Distorted audio at a normal volume on your Episode Amplifier can occur if the LEVEL adjustment for a zone is set too high to compensate for a low source volume. To fix this, readjust the volume levels, starting with baseline settings. Readjust the final volume so that a comfortable maximum volume can be reached without distortion while using the source volume or inline control.
M
Michael DavisAug 14, 2025
What to do if my Episode EA-AMP-HYB-2D-2000 has an inline volume 'thump'?
- M
  Mr. Brad Ramirez DDSAug 14, 2025
  An inline volume 'thump' with your Episode Amplifier typically happens when the amplifier and source volume levels are set too high. To resolve this, calibrate the inline volume controls, ensuring they are one or two adjustment levels away from their maximum setting when the audio is at a normal listening level.
C
Cindy MurphyAug 21, 2025
Why is my Episode EA-AMP-HYB-2D-2000 Amplifier going into protection mode with a blinking red light?
- M
  Mark PowellAug 21, 2025
  Your Episode Amplifier might be going into protection mode due to several reasons: * **High Temperature:** The unit may be overheating. Allow it to cool down to restore normal operation. * **High Current:** The speaker protect limiter may be activated because the rated power has been exceeded. Reduce the input music level. * **Firmware Update:** The amplifier could be updating its firmware (2 Channel blinking). Allow the update to finish.
P
Penny WeeksAug 27, 2025
What to do if my Episode EA-AMP-HYB-2D-2000 Amplifier has a solid red protection LED?
- J
  James JacksonAug 27, 2025
  If your Episode Amplifier shows a solid red protection LED, consider the following: * **Speaker Terminal Short:** Ensure the speaker terminal is fully connected. Channel 2 will light up if a short is detected. * Remove the speaker terminal; if the red light remains solid, investigate further. * **Firmware Update Failure:** Contact Tech Support for firmware recovery if the unit failed to jump to the partition after a firmware update. * Ensure the speaker output is configured correctly (Speaker out). * If the Level Meter shows an audio response but there is still no audio, ensure the source inputs are configured correctly.
A
Andrea PageSep 1, 2025
How to fix distorted audio at normal volume on my Episode EA-AMP-HYB-2D-2000?
- K
  Katelyn ColonSep 1, 2025
  To address distorted audio at normal volume on your Episode Amplifier, readjust the volume levels. Start at baseline settings and readjust the final volume so that a comfortable maximum volume level can be reached without distortion, while using the source volume or inline control.

Episode EA-AMP-HYB-2D-2000 Specifications

General

Channels	2
Frequency Response	20Hz - 20kHz
Total Harmonic Distortion (THD)	< 0.1%
Signal-to-Noise Ratio (SNR)	> 100dB
Input Impedance	20k ohms
Signal to Noise Ratio	> 100dB
Input Sensitivity	1.4V
Amplifier Class	D
Power Output	2000W
Cooling	Fan cooled

Related product manuals

Preview: Episode EA-AMP-HYB-2D-1000

Episode EA-AMP-HYB-2D-1000

Preview: Episode EA-AMP-12D-70

Episode EA-AMP-12D-70

Episode EA-AMP-8D-70A

Preview: Episode EA-AMP-12D-70A

Episode EA-AMP-12D-70A

Preview: Episode EA-AMP-SUB-1D-500

Episode EA-AMP-SUB-1D-500

Preview: Episode EA-AMP-SUB-1D-150

Episode EA-AMP-SUB-1D-150

Episode EA-RSP-16D-100

Episode EA-DYN-12D-100

Preview: Episode E-2100

Preview: Episode E-1230-A

Episode E-1230-A

Preview: Episode ESA-70V2CH-150W

Episode ESA-70V2CH-150W

Preview: Episode DYNAMIC Series

Episode DYNAMIC Series