Epson EB-PU1007B User Manual

324
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio and television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do
not leave cables connected to unused interfaces. Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
For Canadian Users
CAN ICES-3(B)/NMB-3(B)
Parent topic: Notices

Epson EB-PU1007B Specifications

General

Matrix size	0.76 \
Heat dissipation	1465.4 BTU/h
Number of colors	1.07 billion colors
Native aspect ratio	16:10
Projection technology	3LCD
Contrast ratio (typical)	2000:1
Screen size compatibility	- \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, vertical	-45 - 45 °
Keystone correction, horizontal	-30 - 30 °
Projector brightness (economic mode)	4900 ANSI lumens
Light source type	Laser
Service life of light source	20000 h
Service life of light source (economic mode)	30000 h
Throw ratio	0.35 - 10.11:1
Focal length range	varies by lens mm
Interchangeable lens	Yes
3D	No
Video processing	10 bit
Video color modes	Cinema, Dynamic, Natural, Presentation, DICOM simulation mode, Multi-projection, BT.709
Analog signal format system	Not supported
Serial interface type	RS-232C
USB 2.0 ports quantity	2
Noise level	33 dB
Country of origin	Philippines
Noise level (economic mode)	29 dB
Placement	Ceiling, Desktop, Flying frame
Product type	Large venue projector
Product color	Black
Market positioning	Presentation
Cable lock slot type	Kensington
Power source	AC
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	431 W
Power consumption (economy mode)	366 W
Storage temperature (T-T)	-10 - 60 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Bundled software	Inhalt DIY-App, EasyMP Multi PC Projection, Epson Projektor Content Manager, Epson Projektor Management, Epson Projektor Professional Tool
Supported network protocols	HTTPS, IPv6, SNMP, ESC/VP.net, PJLink
Software support	via: Crestron Integrated Partner, Extron IP Link, Extron XTP, AMX Device Discovery
Pallet weight	0 g
Quantity per pack	1 pc(s)
Quantity per pallet	14 pc(s)
Harmonized System (HS) code	85286200

Weight and Dimensions

Depth	436 mm
Width	545 mm
Height	189 mm
Weight	16300 g
Package depth	760 mm
Package width	570 mm
Package height	270 mm
Package weight	21465 g