How To Use Preferences Overview of Preferences
12 13
* Factory Default Settings
To reset the RedLine to its
original factory settings, press
and hold the “VOLUME/MUTE,”
and “SENS,” buttons while
turning the power on. RedLine
will display a Reset message,
accompanied by an audible alert
acknowledging the reset.
1
2
3
4
Pilot HWY
Pilot H
Pilot H.>
Pilot V
Brt Aut
o
Brt Min
Brt Med
Brt Max
Brt Dark
Alamp ON
Alamp OFF
PwrOn FST
PwrOn STD
Meter STD
Meter EXP
Meter SPC
aMute ON
aMute OFF
Voice ON
Voice OFF
Bands DFT
Bands MOD
X ON
or OFF (default is on)
K ON or OFF (default is on)
Ka ON or OFF (default is on)
POP ON or OFF (default is off)
SWS ON or OFF (default is off)
LSR ON or OFF (default is on)
TSR ON or OFF (default is off)
Press the CHG button
to change your setting
within a category
* Full word: Highway or Auto or AutoNoX
Letter: H or A or C
Letter, with scanning dot
Vehicle voltage
* Automatic
Minimum
Medium
Maximum
Full Dark
* Alert Lamp on
Alert Lamp off
* Fast power-on sequence
Standard power-on sequence
* Standard signal strength meter
ExpertMeter
S
pecDisplay
* AutoMute on
AutoMute off
* Voices on
Voices off
* Default settings
One or more bands disabled
Turn bands ON or OFF by pressing
and holding the SENS button
How to customize RedLine
with Preferences
There are 8 user-selectable options so
you can customize your RedLine for your
own preferences. The buttons labeled
VOLUME/MUTE and SENS are also used to
enter Preferences, REVIEW your current
program settings, and to CHANGE any
settings as desired. The words PGM, RVW,
and CHG are located next to the buttons,
and are highlighted in colored graphics.
Pages 14-16 explain each option in more
detail.
How to use Preferences
To enter Preferences, press and hold
both the VOLUME/MUTE and SENS
buttons down for 2 seconds.
The unit will
display the word
Prefs.
Then press the RVW button to review the
current settings. Simply tap the button to
change from item to item.
Press the CHG button to change any
setting. You can either tap the button to
change from setting to setting, or hold the
button to scroll through all the options.
To leave Preferences, simply wait 8
seconds without pressing any button, or
press the PWR button
(
). The unit will
display
Complete return to normal
operation.
An example
Here is how you would turn RedLine’s
AutoMute feature off.
1 Enter Preferences by holding both the
VOLUME/MUTE and SENS buttons down for
2 seconds. RedLine will beep display
Prefs.
2 Then hold the RVW button down.
RedLine will scroll through the categories,
starting with Pilot, Brightness, Alert Lamp
(Alamp), Power-on sequence (PwrOn),
Signal strength meter
(Meter), and then
AutoMute
(aMute).
3 Release the RVW button when RedLine
shows the AutoMute item. Since the factory
setting is for AutoMute to be on, RedLine will
display aMute ON.
If you accidentally don’t release the RVW
button in time, and RedLine goes to the next
category, simply hold the RVW button down
again and it will scroll through all of the
categories.
4 Press the CHG button to change from
aMute ON to aMute OFF.
5 To complete or exit Preferences, simply
wait 8 seconds without pressing any button,
or press the PWR button (
). RedLine will
display
Complete and return to normal
operation.
Press the RVW button
to go fro m one category
to the next
PILOT LIGHT
(Power-on indication)
BRIGHTNESS
ALAMP
(Alert Lamp)
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
VOICE
BANDS
To Next Page
Loading...
