Esko Kongsberg XN IPC 2.0 - User Manual

Kongsberg XN / iPC 2.0
User Manual
01 - 2017 | XN

Summary

5. Safety Regulations

5.1 Introduction and Responsibilities

General safety overview, hazards, and definitions of responsibilities.

5.3 Operator Requirements & 5.4 Definition of Use

Operator qualifications and clarification of intended vs. non-intended use.

5.5 Danger Zones

5.5.1 Danger Zone Identification

Identifies and describes the danger zone around moving parts.

5.5.2 Hazard Warnings

Highlights hazards from moving parts, laser radiation, and high voltage.

5.5.3-5.5.5 Safety Precautions

5.6 Warning Sign Explanations

8. Prepare for a Job

8.1 Introduction and Job Creation

Introduction to job prep, safety, and steps for creating a new job.

8.4-8.7 Job Configuration

8.8 Job Execution and 8.9 Milling Production

10. System Setup

10.1 Introduction and Factory Adjustments

10.2-10.3 Installation Adjustments

10.4-10.5 Ruler and Reference Point Setup

11. Tool Configuration and Adjustment

11.2 Adjust Active Tool

Executing tool adjustment wizards from the Adjust Selected Tool dialog.

11.3-11.4 Tool Calibration and Lag Settings

11.5 Rotation Adjustment

11.6 Center Offset Adjustment

11.9 Maintain Tool List

12. Tooling System

12.1 Tool Handling and Care

Guidelines for proper handling, care, and cleaning of tools.

12.2 Tool Inserts with Built-in Motor

12.3 Tool Heads Overview

12.5 FlexiHead Tool Head Description and Adjustments

12.6 PowerHead Tool Head Description and Adjustments

12.6.1-12.6.2 Crease Tools

12.6.3 Perforation Wheel

Perforation Wheel Tool Adjustment

12.6.4 HD Knife Tool and 12.6.5 V-notch Knife

13.13.1 V-notch Knife Tool Adjustment

12.7 FoamHead Tool Head Description

12.8 MultiCUT-HP Introduction and Safety

12.8.1 MultiCUT-HP Spindle Motor Specs

12.8.2 MultiCUT-HP Chucks and Replacement

MultiCUT-HP Tool Head Components

12.8.3 Safety Issues for MultiCUT-HP

12.8.4 Precautions for Spindle and Bits

12.8.5 Bit Clamping, Storage, and Spindle Replacement

12.8.6-12.8.7 Cleaner Device and Bit Change

Router Bit Insertion and Replacement Steps

12.8.8 Chuck Change and Cleaning

Chuck Change Procedure Part 1

12.8.9-12.8.10 Bit Slipping and Bit Dimensions

12.8.11-12.8.12 False Air Valve and Tool Adjustment

12.8.13 Table Top and Height Adjustment

12.9.2 Chiller Error Conditions and Flow

12.10.2-12.10.3 Chiller2016 Startup and Errors

12.11 Measuring Foot Functions

12.12 Laser Pointer Usage

12.13 X-Pad Calibration

12.13.2-12.13.3 X-Pad Tool Depth and Limitations

13. Tool Inserts

13.1 Ball Point Pen Tool

Ball Point Pen Tool Adjustments

13.2 Bevel Knife

Bevel Knife Blade Replacement

Steps for replacing the knife blade in the Bevel Knife tool.

Bevel Knife Cutting Depth

13.3 Bevel Knife U20 and 13.4 Braille Tool

Braille Tool Sphere Addition

Braille Tool Setup and Offset Adjustment

Braille Tool Parameters and Layer Preparation

13.5 CorruSpeed Knife and Pressure Adjustment

13.5.1 CorruSpeed Knife Tool Adjustment

13.6 Crease Tool and Adjustment

13.8 Drill Tools and Flexi Drill Tool

13.8.2 Reboard Drill Tool and Bit Dimensions

13.9 Foam Knife Tool Details

13.10 Ink Tool Models

13.11 KissCut Tool Details

13.12 MicroCut Tool Details

13.13 Psaligraphy Knife Tool

13.14 RBI 90-16 Rigid Board Insert

13.15 Reciprocating Knife Models

13.16 Rigid Material Knife

13.17 RotaCut Tool and Adjustment

13.18 Static Knife

13.19 VI45 Knife Tool

15. Fuse Replacement

15.1 MPU Fuses

15.2-15.3 X1 and X2 Fuses

15.4 Y;Z Fuses

15.5 Tool Rotation;Reciprocating Knife Fuses

15.6 Chiller Fuse Replacement

Esko Kongsberg XN IPC 2.0 Specifications