19
MODEL 746
Power supply (Vac +6% -10% 50-60Hz) 230
Absorbed power (W) 300
Reduction ratio 1 : 30
Type of pinion Z20 - Z16
Rack Module 4 - step 12.566
Max. thrust (daN) 50 (Z20) - 62,5 (Z16)
Max. Torque (Nm) 20
Winding thermal protection (°C) 120
Use frequency 70% (see graph)
Oil quantity (l) 1,8
Type of oil FAAC XD 220
Operatine ambient temperature (°C) -20 ÷ +55
Gearmotor weight (Kg) 14
Protection class IP 44
Gate max. weight (Kg) 400 (Z20) - 600 (Z16)
Gate speed (m/min) 12 (Z20) - 9,6 (Z16)
Gate max. length (m) (time-out) 50 (Z20) - 40 (Z16)
Clutch twin-disk in oil bath
Protective treatment cataphoresis
Equipment 780D
Limit-switch MSL or inductive
Gearmotor overall dimensions LxHxD (mm) see Fig. 2
Electric motor technical specifications
RPM 1400
Power (W) 300
Absorbed current (A) 1.5
Starting capacitor (µF) 25
Power supply (Vac +6% -10%; 50-60Hz) 230
% Freq.
Utilizzo
% Fréq.
d’utilisation
Duty
Cycle
0
10
20
30
40
50
60
70
80
90
100
123456789101112
Tempo (h) Time (h)
Temps (h) Zeit (h) Tiempo (h) werktijd (h)
These instructions apply to the following models:
746 ER Z16 - 746 ER Z20 - 746 ER CAT - 746 ER RF
The FAAC mod. 746 automated system for sliding gates is an
electro-mechanical operator transmitting motion to the sliding leaf
via a rack or chain pinion appropriately coupled to the gate.
The non-reversing system ensures the gate is mechanically locked
when the motor is not operating and, therefore, no lock needs to be
installed.
The gearmotor is equipped with a mechanical clutch which,
combined with an electronic device, offers the necessary adjustable
anti-crushing safety and guarantees stopping or reversing the gate
movement. A handy manual release makes it possible to move the
gate in the event of a power cut or malfunction. The electronic
control equipment is equipped with a gearmotor and is housed
inside the operator.
The 746 automated system was designed and manufactured to
control access of vehicles. Avoid any other use whatever.
Tab. 1 TECHNICAL SPECIFICATIONS OF 746 GEARMOTOR
where:
Ta = opening time
Tc = closing time
Tp = pause time
Ti = time of interval between two complete cycles
Use frequency graph
Securing corners
Pinion
Limit sensor switch
Operator cover
780 D Control board
Adjustment screw for
anti-crushing clutch
Oil filling plug
Operator earthing
Lever operated release system
Protective side panels
Cover for 780D control board
AUTOMATED SYSTEM 746 & ELECTRONIC CONTROL UNIT 780D
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS
1.1. MAXIMUM USE CURVE
The curve makes it possible to establish maximum work time (T)
according to use frequency (F).
E.g.: The 746 gearmotor can operate non-stop at 70% use
frequency.
To ensure efficient operation, operate in the work range below the
curve.
Important: The curve is obtained at a temperature of 24°C. Exposure
to the direct sun rays can reduce use frequency down to 20%.
Calculation of use frequency
The percentage of effective work time (opening + closing) compared
to total time of cycle (opening + closing + pause times).
Calculation formula:
Ta + Tc
%F =
X 100
Ta + Tc + Tp + Ti
Fig. 1
To Next Page
Loading...
