E045S 9 532373 - Rev.A
Translation of the original instructions
ENGLISH
5.3 CONNECTIONS
F
Carry out the connections with the power supply
disconnected.
CONTROL DEVICES
i
Multiple NO contacts on same input must be con-
nected in parallel.
Multiple NC contacts on same input must be con-
nected in series.
Below is a brief explanation of the inputs. The effect
a command has may vary according to the operating
logic and programming functions.
■ Connecting the devices to terminal board J3:
J9
F+/R1 -/R2
RADIO
2EASY
CONNECTIVITY
USB-A
MAIN
PE
N
L
230 V~
9 10 11
20 21
LAMP
M1 M2
M M
1PE N L 2 3 4 5 6 7 8
COM
OP
CL
COM
OP
CL
C C
230 V~
60 W max
24 V
"
3 W max
115V-F10A
230V-F5A
T0.8A
15 16
OP-A
OP-B
STOP
J3
J3
J9
9 OP-A
(TOTAL motion command)
NO contact, connect a push-button or another type
of pulse generator which, by closing a contact, com-
mands the total opening (OPEN) of the gate.
10 OP-B
(Motion command determined by the set operating
logic)
NO contact, connect a push-button or another type of
pulse generator which, by closing a contact, causes the
gate to close (CLOSE in logics c , b) or PARTIAL open
(in all other logics):
The partial opening is:
• 50% of the complete opening in systems with only
one motor
• complete only for the leaf actuated by motor 1 in
two motor systems
11 STOP
(Stop command)
NC contact, connect a push-button or another type of
pulse generator which, by opening a contact, causes
the automation to stop.
i
The board is supplied with the STOP is
bridged with the common contacts(-).
If the input is not used, keep it bridged
with the common contacts (-).
BUS 2EASY DEVICES
J10
2EASY
CONNECTIVITY
USB-A
MAIN
PE
N
L
230 V~
9 10 11 20 21
LAMP
M1 M2
M M
1PE N L 2 3 4 5 6 7 8
COM
OP
CL
COM
OP
CL
C C
230 V~
60 W max
24 V
"
3 W max
115V-F10A
230V-F5A
T0.8A
15 16 17 18
OP-A
OP-B
STOP
+24V
+24V
W.L.
LOCK
i
If no BUS 2easy devices are used, leave the terminals
free.
For connecting and assigning addresses see § Ac-
cessories.
Do not exceed the maximum load of 500 mA.
ACCESSORIES POWER SUPPLY
J9
F+/R1 -/R2
RADIO
2EASY
CONNECTIVITY
USB-A
MAIN
PE
N
L
230 V~
9 10 11 20 21
LAMP
M1 M2
M M
1PE N L 2 3 4 5 6 7 8
COM
OP
CL
COM
OP
CL
C C
230 V~
60 W max
24 V
"
3 W max
115V-F10A
230V-F5A
T0.8A
15 16 17 18
+24V
+24V
The E045S supplies 24 V
"
and is short-circuit pro-
tected with a maximum current of 500 mA for con-
nected accessories.
15 , 16
-
Common contacts / Accessories power supply
negative
17 , 18 +24V Accessories power supply positive
LED OUTPUT
J11
J11
J9
J9
F+/R1 -/R2
RADIO
2EASY
CONNECTIVITY
USB-A
MAIN
PE
N
L
230 V~
9 10 11 20 21
LAMP
M1 M2
M M
1PE N L 2 3 4 5 6 7 8
COM
OP
CL
COM
OP
CL
C C
230 V~
60 W max
24 V
"
3 W max
115V-F10A
230V-F5A
T0.8A
15 16 17 18
OP-A
OP-B
STOP
+24V
+24V
W.L.
LOCK
24 V
"
3 W max
The E045S has an Open Collector output for connect-
ing a LED (24 V
"
, 3 W max) in order to check the status
of the gate remotely.
To Next Page
Loading...
