Falcon F25/90 - Page 7

Bladsy/ Page 7
STEL DIE TREKKER SE BO-ARM TOT DIE REGTE LENGTE
Dit is belangrik om u trekker se bo-arm so te stel dat die implement se topmas in die regop
posisie is wanneer die implement op gelyk grond rus. Dit sal die implement toelaat om op die
volle lengte van sy glystukke te loop en ’n eenvormige snyhoogte oor ongelyke oppervlakke te
verseker.
Dit sal ook help verseker dat die kragaftakkeras nie aan die voorste deel van die implement raak
wanneer dit opgelig is nie. Sou die kragaftakkeras egter steeds aan die implement raak, beperk
die hoogte deur die stop op die hidrouliesebeheer-vlak te stel.
GAAN ALLE BOUTE NA EN DRAAI HULLE VAS
Verseker dat alle boute heeltemal vas is voor gebruik en dan weer ná die eerste paar uur se
gebruik. Dit is baie belangrik om die boute aan die snymeganisme dikwels na te gaan en vas te
draai.
MAAK SEKER DAT DIE STOFSKERM OOR DIE LEWERINGSAS IN DIE
REGTE POSISIE IS (aan die F50, F80 en F80EV)
Dit is noodsaaklik dat die skerm onder u ratkas in die regte posisie moet wees. Dit is om te
verseker dat gras, tou of draad nie om die onderkant van die leweringsas draai en die onderste
olieseëls van die ratkas beskadig nie. Skade aan hierdie seëls kan al die ratkasolie laat uitloop.
Die twee boute wat hierdie stofskerm onder u Falcon-wentelsnyer vashou, moet nagegaan en,
indien nodig, vasgedraai word. Die stofskerm moet so laag as moontlik geposisioneer wees en
die ens van die ratkas se leweringsas heeltemal bedek.
SLAAN AG OP DIE VEILIGHEIDSREËLS
Gee u drywer asseblief opdrag om die volgende reëls streng na te kom:
• Moenie van die trekker afklim terwyl die enjin loop nie en verseker dat dit afgeskakel is
voordat enige verstellings gemaak word.
• Voordat onder die implement gewerk word om lemme te vervang of boute vas te draai, laat
sak eers die raam op ’n staander of stut of op die grond.
• Wees bewus van enige hindernisse, soos stompe, bottels, blikkies ens. Verwyder hulle van
die land voordat met werk begin word, of vermy hulle ten minste.
• Ontmoedig toeskouers en moet nooit passasiers dra nie. Onthou, klein klippies ens. kan
teen hoë spoed uitvlieg en ernstige beserings veroorsaak.
• Moet niemand toelaat om naby die wentelsnyer te kom terwyl dit werk nie.
• Beheer die trekker só dat die optimale kragaftakkerspoed van ongeveer 540 opm gehand-
haaf word. ’n Te lae kragaftakkerspoed sal die dryfasstelsel oorlaai. ’n Te hoë spoed sal die
taak gevaarlik maak.
• Moet niemand toelaat om hulle hande of voete onder die wentelsnyer in te druk terwyl die
trekkerenjin loop nie.
ADJUST THE TRACTOR TOP-LINK TO THE CORRECT LENGTH
It is important to adjust your tractor top-link so that the implement topmast is in the vertical
position when the implement is resting on level ground. This will allow the implement to run on
its full skid runner length, ensuring a uniform cutting height when running over uneven lands.
This will also help to ensure that the PTO shaft does not come into contact with the front of
the implement when it is in the raised position. However, should the PTO shaft still touch the
implement, limit the height by setting the stop on the hydraulic control level.
CHECK AND TIGHTEN ALL BOLTS
Check that all bolts are fully tightened before use and then again after the rst few hours of use.
It is very important that the bolts on the cutting gear are checked and tightened frequently.
CHECK THAT THE DUST COVER OVER THE OUTPUT SHAFTS IS IN THE
CORRECT POSITION (Fitted on the F50, F80 and F80EV)
It is essential that the cover under your gearbox is in the correct position. This is to ensure that
grass, twine or wire does not wrap around the base of the output shaft and damage the lower oil
seals of the gearbox. Damage to these seals could drain the gearbox oil. The two bolts securing
this dust cover under your Falcon Slasher should be checked and tightened if necessary. The
dust cover should be positioned as low as possible and should cover the ange of the gearbox’s
output shaft completely.
TAKE NOTE OF THE SAFETY RULES
Please instruct your driver to adhere to the following rules:
• Do not get off the tractor while it is running, and ensure that the tractor is turned off before
making adjustments.
• When working under the implement, changing the blades or tightening the bolts, the frame
should be lowered on to a stand, a prop or the ground.
• Be aware of any obstruction such as stumps, stones, bottles, tins, etc. Remove these from
the eld before starting work or at least avoid them.
• Discourage spectators and never carry passengers. Remember, it is possible that small
stones can y out at high speed. These projectiles can cause serious injury.
• Do not allow anyone to walk near the slasher while it is operating.
• Operate the tractor in such a way that you establish and maintain the optimum PTO speed
of approximately 540 rpm. Too low a speed will overload the drive shaft system. Too high a
PTO speed will make the operation dangerous.
• Do not allow anyone to put their hands or feet under the slasher while the tractor is running.
• Do not remove the protective covers around the PTO shaft or aps provided on the
implement.
5. 5.
6.
6.
7.
7.
8.
8.