To Next PageTo Next PageWhat to do if my Ferroli BLUEHELIX TECH A shows incorrect system water pressure?
If your Ferroli Boiler displays 'Incorrect system water pressure', it could be because: * The pressure is too low. Fill the system to the correct pressure. * The water pressure switch is damaged or not connected. Check the sensor.
How do I fix a card parameter fault on my Ferroli BLUEHELIX TECH A?
If your Ferroli Boiler shows 'Card parameter fault', it is likely due to a wrong card parameter setting. Check the card parameter and modify it if necessary.
Why does my Ferroli Boiler show flame present signal with burner off?
If your Ferroli Boiler displays 'Flame present signal with burner off', it could be due to: * Electrode fault. Check the ionisation electrode wiring. * Card fault. Check the card.
What causes controller fault ABM03C in Ferroli BLUEHELIX TECH A Boiler?
If your Ferroli Boiler is showing a 'Controller fault ABM03C' due to an internal error, check the earth connection. If the problem persists, replace the controller.
How to troubleshoot no communication between controller and gas valve in Ferroli BLUEHELIX TECH A?
If your Ferroli Boiler displays 'No communication between controller and gas valve', it could be due to: * The controller not being connected. Connect the controller to the gas valve. * A damaged valve. Replace the valve.
What to do if exchanger protection intervention occurs in Ferroli BLUEHELIX TECH A?
If your Ferroli Boiler is experiencing 'Exchanger protection intervention', it could be due to: * No system water circulation. Check the circulating pump. * Air in the system. Vent the system to remove the air.
How to fix a heating sensor fault on a Ferroli BLUEHELIX TECH A?
If your Ferroli Boiler is showing a 'Heating sensor fault' it could be due to a damaged sensor. Replace the sensor to resolve this issue.
What causes no flame after ignition stage in my Ferroli Boiler?
If your Ferroli Boiler displays 'No flame after ignition stage', it could be due to several potential causes: * There may be an ionisation electrode fault. Check the position of the ionisation electrode and replace it if necessary. * The flame might be unstable. Inspect the burner. * There could be a gas valve Offset fault. Check the Offset adjustment at minimum power. * The air/fume ducts might be obstructed. Remove any obstructions from the flue, fume extraction ducts, air inlet, and terminals. * The trap might be blocked. Check the trap and clean it if necessary.
Why is overtemperature protection intervention happening in my Ferroli Boiler?
If you are experiencing 'Overtemperature protection intervention' with your Ferroli boiler, it could be due to a few reasons: * The heating sensor may be damaged. Check its correct positioning and operation. * There might be no water circulation in the system. Check the circulating pump. * There could be air in the system. Vent the system to remove any trapped air.
What to do if my Ferroli BLUEHELIX TECH A Boiler has no burner ignition?
If your Ferroli Boiler shows 'No burner ignition', there could be several reasons: * There might be no gas flow. Ensure there is regular gas flow to the boiler and that air has been eliminated from the pipes. * There could be an ignition/detection electrode fault. Check the wiring and positioning of the electrode, ensuring it's free of deposits. * The gas valve might be faulty. Inspect the gas valve and replace it if necessary. * The gas supply pressure could be insufficient. Verify the gas supply pressure. * The trap might be blocked. Inspect the trap and clean it if needed.
General| Type | Condensing Boiler |
|---|---|
| Weight | 32 kg |
| Modulation Range | Up to 1:10 |
| Combustion Chamber | Stainless Steel |
| Warranty | 2 Years |
| Efficiency | Up to 98% |
| Fuel Type | Natural gas / LPG |
| Control Panel | Digital |
