Need help?Do you have a question about the Foison C24 and is the answer not in the manual?
Lists standard accessories included with the cutter, detailing items like cables, pen, and software.
Illustrates the installation of vertical stands for the C48 model.
Lists optional accessories available for the cutter, such as software.
Details the optional software packages like Artcut, Flexi, and PCSIGN.
Provides essential safety guidelines and explains warning symbols to ensure safe operation.
Details technical specifications and parameters for C12, C24, and C48 models.
Identifies and labels the parts visible from the front of the C-24 model.
Identifies and labels the parts visible from the back of the C-24 model.
Explains the functions of each button and the LCD display on the cutter's control panel.
Covers the initial setup, including cutting environment and connecting the cutter to a PC.
Specifies ideal conditions and locations for installing the cutting plotter.
Guides on connecting the cutter to a computer using RS232 or USB interfaces.
Step-by-step instructions for installing the necessary USB driver for PC connection.
Details how to properly connect the power cable to the cutter and power source.
Provides instructions and cautions for loading and preserving cutting media.
Explains how to install cutting tools, including knife adjustment and trial runs.
Introduces different tools and their applications with the cutting plotter.
Guides on performing trial cuts to optimize knife protrusion and pressure for precise cutting.
Instructions on how to install and use the plot pen for drawing functions.
Explains the different operational statuses of the cutter, such as Online and Offline.
Details how to switch between Online and Offline modes and their implications.
Describes how to control the movement of the carriage using the control panel buttons.
Guides on setting the starting point (origin) for cutting operations.
Explains the function of the bounded system that prevents the carriage from exceeding work area.
Defines the functions of the buttons on the control panel when operating online.
Details the functions of the control panel buttons when operating in offline mode.
Explains the keyboard functions available in offline status.
Explains how to navigate and operate the cutter through its menu system.
Describes the initial display shown when the cutter is powered on.
Explains the procedure for switching between Online and Offline modes during operation.
Guides on adjusting the cutting speed and the force applied by the knife.
Describes how to perform a test to check the knife's drop and raise function.
Explains how to perform a test cut of a rectangle to verify settings.
Details how to use the pause button to temporarily stop and resume cutting operations.
Explains how to adjust speed and knife force while the cutter is actively working.
Describes how to repeat the last cutting job performed by the cutter.
Guides on configuring communication port settings like baud rate for data transfer.
Explains how to adjust the X and Y axis scale for accurate cutting output.
Details how to set output parameters and port configurations within the ARTCUT software.
Explains how to apply ploter compensation for precise character cutting.
Addresses issues with character deformation during small engravings and provides solutions.
Explains causes and solutions for zigzag patterns occurring during cutting operations.
Discusses reasons for paper deviation and suggests adjustments for smoother feeding.
Covers causes of plotting output failures or machine lock-ups and their remedies.
Addresses issues related to the machine's casing feeling tingly or causing shock, focusing on grounding.
Troubleshoots issues with job smoothness and sharp angle performance during plotting.
Provides solutions for cases where the LCD display is blank or shows garbled characters.
Explains how to resolve issues where character strokes do not close properly during cutting.
Offers solutions for problems where letters are not fully cut or missed during the process.
Provides guidelines on daily cleaning and long-term maintenance for the cutting plotter.
Details how to prepare and output designs from CorelDraw for the cutting plotter.
Provides instructions on installing and configuring CorelDraw for optimal use with the cutter.
Guides on setting communication ports and troubleshooting related hardware issues.
General| Motor Type | Stepper Motor |
|---|---|
| Category | Plotter |
| Max Cutting Width | 600 mm |
| Interface | USB |
| Power Supply | AC 110V-220V, 50/60Hz |
| Control Panel | LCD with buttons |
| Resolution | 0.025 mm |
| Media Thickness | 0.8 mm |
To Next Page
