Fostex VF-16 - Page 16

16
15. [EFF EDIT-EFF1/MUTE] Key
* This is used to CHECK/CHANGE the EFFECT type and
parameter settings of EFFECT 1.
* Press this key while the [SHIFT] key is depressed to
turn ON/OFF the mute feature of EFFECT 1.
16. [EFF EDIT-EFF2/MUTE] Key
* This is used to CHECK/CHANGE the effect type and
parameter settings of EFFECT 2.
* Press this key while the [SHIFT] key is depressed to turn
ON/OFF the mute feature of EFFECT 2.
17. [CH PARAM EDIT-EFF1/EFF2/PRE/POST] Key
* This is used to CHECK/CHANGE the send level settings
of EFFECT 1 or EFFECT2. The EFFECT 1 and EFFECT 2
settings alternate every time the key is pressed.
* Press this key while the [SHIFT] key is depressed to
CHECK/CHANGE the PRE/POST settings of EFFECT 1
or EFFECT 2.
* Use the [CH STATUS/CH SEL] Key to select the channel
to change any settings together.
18. [CH PARAM EDIT-EQ/COMP-HI/G/F/Q/COMP] Key
* This is used to CHECK/CHANGE the high frequency
parametric equalizer settings. The parameter settings
alternate every time the key is pressed.
* Press this key while the [SHIFT] key is depressed to
CHECK/CHANGE the COMPRESSOR settings.
* Use the [CH STATUS/CH SEL] Key to select the channel
to CHECK/CHANGE any settings together.
19. [CH PARAM EDIT-AUX1/AUX2/PRE/POST] Key
* This is used to CHECK/CHANGE the send level settings
of AUX 1 or AUX 2. The AUX 1 and AUX 2 settings
alternate every time the key is pressed.
* Press this key while the [SHIFT] key is depressed to
CHECK/CHANGE the PRE/POST settings of AUX 1 or
AUX 2.
* Use the [CH STATUS/CH SEL] Key to select the channel
to change any settings together.
20. [CH PARAM EDIT-EQ/COMP-MID-G/F/Q] Key
* This is used to CHECK/CHANGE the midrange
frequencies of the parametric equalizer settings.
* Press this key while the [SHIFT] key is depressed to
CHECK/CHANGE the settings.
21. [CH PARAM EDIT-PAN/FADER] Key
* This is used to CHECK/CHANGE the PAN settings.
* Press this key while the [SHIFT] key is depressed to
show the current fader location. Finer level
adjustment is possible by using the [JOG] dial.
* Use the [CH STATUS/CH SEL] key to select the channel
to change any settings together.
22. [CH PARAM EDIT-EQ/COMP-LO-G/CH VIEW] Key
* This is used to CHECK/CHANGE the low frequencies
of the parametric equalizer settings.
* Press this key while the [SHIFT] key is depressed to
show the settings of the selected channel.
* Use the [CH STATUS/CH SEL] key to select the channel
to change any settings together.
23. [MASTER CH STATUS/CH SEL] Key
* This becomes the master channel ON/OFF key when
the LCD is in the normal display mode (described
later).
* Select the channel to CHECK/CHANGE any settings
with the ([CH PARAM EDIT] Key (No. 17-22)] to
CHECK/CHANGE any PAN, equalizer or other mixer
settings.
* The STATUS of the key lights ON are defined below.
[GREEN]: The level of the stereo buss L, R outputs are
adjustable with the fader.
[OFF]: The signals to the master fader are [MUTE]
(no sound).
24. [MASTER] Fader
* This is used to adjust the master level of the sound
signals output from the STEREO OUT L, R jacks.
For more details, refer to the respective instructions
of each item.