How to troubleshoot a Franke Freezer that does not run?
If your Franke Freezer isn't running, first ensure the rocker switch is in the ON position. If that's not the issue, check if the electronic controller has been turned off by pressing and holding the power button (located in the top- right corner of controller) for 5-7 seconds. Finally, inspect the circuit breaker to see if it has tripped and reset it if necessary.
Why is the product in my Franke Freezer above the target temperature?
If the product in your Franke Freezer is above the target temperature, it could be due to a high ambient temperature in the store. In this case, decrease the set point temperature of the controller. Also, ensure that food is pre-chilled before placing it in the drawers; put the product into cold storage until its temperature is within food safety limits.
What to do if Franke HCMF-30P Freezer is running, but not reaching target temperature?
If your Franke Freezer is running but not reaching the target operating temperatures, it could be due to several reasons. The store’s ambient temperature might be too high, so decrease the set point temperature of the controller. The condenser coil might be dirty or clogged with debris; use a soft bristle brush to clean the coils. Alternatively, ice buildup on the evaporator coils could be the issue; remove all product, defrost the unit, and allow sufficient time for it to reach the target operating temperature.
Why is frost building up on the opening around the door of my Franke HCMF-30P?
If you notice frost building up on the opening around the door of your Franke Freezer, the door gasket may be damaged or not installed correctly. Verify that the door gasket is installed correctly and is not cracked or damaged.
Explains DANGER, WARNING, CAUTION, and NOTICE symbols.
Details electrical safety measures to prevent shock, explosion, or arc flash.
Outlines hazards associated with R-290 refrigerant and refrigeration systems.
Warns against unauthorized modifications and stresses using OEM parts for safety.
Lists and illustrates major parts of the High Capacity Meat Freezer (HCMF-P).
Covers removing protective materials and positioning the unit correctly with clearance.
Details steps for reversing the front door and attaching the glove holder bracket.
Instructs on plugging the unit into an appropriate electrical receptacle.
Provides steps to remove the front loading door by detaching hinges.
Guides on reattaching hinges and mounting the door in the reversed position.
Explains the location and function of the power switch and temperature controller.
Details the procedure for setting the desired temperature using the controller.
Lists factory preset and adjustable temperature ranges for the freezer.
Outlines the steps to initiate a manual defrost cycle if needed.
Describes how to adjust the height of the middle wire shelf for different box sizes.
Details loosening, sliding, and re-securing shelf rails for height adjustment.
Guides on loading frozen product, case handling, and maintaining temperature.
Emphasizes not leaving the door open and ensuring the roll-back lid closes properly.
Lists causes/remedies for unit not powering on or maintaining temperature.
Provides solutions for frost formation around the door and gasket integrity.
Details warranty period for Franke parts and exclusions.
Explains how warranties for non-Franke equipment are handled.
Explains DANGER, WARNING, CAUTION, and NOTICE symbols.
Details electrical safety measures to prevent shock, explosion, or arc flash.
Outlines hazards associated with R-290 refrigerant and refrigeration systems.
Warns against unauthorized modifications and stresses using OEM parts for safety.
Lists and illustrates major parts of the High Capacity Meat Freezer (HCMF-P).
Covers removing protective materials and positioning the unit correctly with clearance.
Details steps for reversing the front door and attaching the glove holder bracket.
Instructs on plugging the unit into an appropriate electrical receptacle.
Provides steps to remove the front loading door by detaching hinges.
Guides on reattaching hinges and mounting the door in the reversed position.
Explains the location and function of the power switch and temperature controller.
Details the procedure for setting the desired temperature using the controller.
Lists factory preset and adjustable temperature ranges for the freezer.
Outlines the steps to initiate a manual defrost cycle if needed.
Describes how to adjust the height of the middle wire shelf for different box sizes.
Details loosening, sliding, and re-securing shelf rails for height adjustment.
Guides on loading frozen product, case handling, and maintaining temperature.
Emphasizes not leaving the door open and ensuring the roll-back lid closes properly.
Lists causes/remedies for unit not powering on or maintaining temperature.
Provides solutions for frost formation around the door and gasket integrity.
Details warranty period for Franke parts and exclusions.
Explains how warranties for non-Franke equipment are handled.
To Next Page
General
