Fujitsu ARTG45LHTB User Manual

En-20
Notes
Possible temperature setting ranges in the operation •
modeareasfollows:
Cool, Dry, Auto ............... 18to30°C(64to88°F)
Heat ............................... 16to30°C(60to88°F)
If the temperature out of the Set temp. range limitation •
is set, it will be reset at the nearest temperature within
the range. However, the adjusted temperature value
in this setting will not be corrected automatically.
(7) Select [Zone (single)] (individual setting of zone control)
or [Zone (group)] (simultaneous setting of zone control)
asfollows:
Individual setting of zone control):
Select [Zone (single)] with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to move
the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(
sin
g
le
)
Sensor:
Select the room-temperature sensor with the [Cur-
sor button (Up/Down)]. Then press the [Cursor button
(Right)] to move the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(
sin
g
le
)
Sensor
Zone 1
Secondar
y
RC
Zone 2
Zone 3 Zone 4
Zone 5 Zone 6
Zone 7 Zone 8
Select applicable zone name with the [Cursor button
(Left/Right)], and press the [Cursor button (Up/Down)]
to mark a check.
Check-marked: The zone is air-conditioned.
Blank: The zone is not air-conditioned.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(
sin
g
le
)
Sensor: Secondary RC
Zone 1 Zone 2
Zone 3 Zone 4
Zone 5 Zone 6
Zone 7 Zone 8
After you select all the applicable zones, press the
[Enter button] to complete the individual setting of zone
control.
Notes
When you set “On timer”, you need to set all of •
operating mode, temperature, room-temperature
sensor, and applicable zone(s).
Withoutthesecongurations,thetimerwillnotwork.
Depending on the initial setup in the installation, there •
is a case that at least one zone need to be selected.
In that case, following message is displayed on the
screen, and you need to put a check mark at least one
zone
XXXXXX
XXXXXX
One zone must be open at all times.
Simultaneous setting of zone control):
Select [Zone (group)] with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to move
the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(group)
Select the applicable group with the [Cursor button (Up/
Down)].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(group)
Day
To complete the simultaneous setting of zone control,
press the [Enter button].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Back:
Setting:
Heat
20
°
C
Zone
(
group
)
Day
(8) When setting the other days of the week continually,
perform procedures in step 4 and 5.
9374379866_OM_EN.indd 20 17/12/2014 13:19:30

Fujitsu ARTG45LHTB Specifications

General

Brand	Fujitsu
Model	ARTG45LHTB
Category	Air Conditioner
Language	English