Fujitsu ETERNUS LT60 S2 User Manual (English)

Other manuals for Fujitsu ETERNUS LT60 S2

User Guide70 pages

Manual11 pages

Questions and Answers:

T
Tara HernandezAug 14, 2025
Why is my Fujitsu ETERNUS LT60 S2 performance so bad?
- C
  Calvin CrawfordAug 14, 2025
  Poor Fujitsu Storage performance can stem from several factors. Try using a new cartridge, as a marginal one can cause performance issues due to bad spots on the tape. Backing up data that compresses poorly or is already compressed can lower performance. Small file sizes can also impact performance. Confirm that your backup application uses block sizes of at least 32KB, preferably 64KB, referring to its documentation for details. Check the network bandwidth from the host computer, comparing to a local-only backup if backing up over a network. Ensure the backup server has enough memory to handle the backup or restore bandwidth. Cleaning the tape drive may also help.
J
Jeffery MontgomeryAug 17, 2025
What to do if I cannot write to or read from tape on Fujitsu Storage?
- G
  georgesanchezAug 17, 2025
  If you cannot write to or read from tape on your Fujitsu Storage, ensure the cartridge is write-enabled by moving the write-protect switch. Verify you're using the appropriate data cartridge for your library model and that it hasn't been degaussed. Ultrium cartridges should not be degaussed. Check that the cartridge hasn't been exposed to harsh conditions or physically damaged. If the cartridge was created using a different backup application, you may need to erase, format, or label it. Understand any data protection or overwrite protection schemes your backup application uses. Retry with a known good tape and consider cleaning the tape drive.
A
Alicia OwenAug 20, 2025
How to fix Fujitsu ETERNUS LT60 S2 library that does not power on?
- X
  xandersonAug 20, 2025
  If your Fujitsu Storage library doesn't power on: * Check all power cord connections. * Ensure the power switch on the front panel is in the ON position. * Verify power to the outlet by trying another working outlet. * Replace the power cord.
B
Becky WadeAug 25, 2025
What to do if no display messages appear on Fujitsu ETERNUS LT60 S2 Storage?
- J
  James TaylorAug 25, 2025
  If no display messages appear on your Fujitsu Storage, first ensure the power cord is connected and the power switch is on. Try power cycling the library. You can also try downloading the library firmware.
K
Kristen GonzalezAug 27, 2025
How to eject a tape stuck in Fujitsu Storage drive?
- E
  Elizabeth CarpenterAug 27, 2025
  If a tape is stuck in the drive of your Fujitsu Storage, power cycle the library and allow it to complete initialization (which can take up to 10 minutes). Then, retry unloading the tape using the library operator control panel. Allow the tape drive to complete all operations, which may take up to ten minutes if the library was reset while the cartridge was positioned at the physical end of the media. Ensure that the backup software isn't reserving the slot or preventing the tape drive from ejecting the cartridge. Temporarily disconnect the library from the host server and power cycle to eliminate the host as the problem source.
C
Chris SimpsonAug 30, 2025
What to do if cleaning or data cartridge is incompatible with Fujitsu ETERNUS LT60 S2 Storage drive?
- J
  John LeeAug 30, 2025
  If a cleaning or data cartridge is incompatible with your Fujitsu Storage drive, make sure you are using cartridges that are compatible with the drive and model of your library. The library automatically unloads incompatible cartridges, the Media Attention LED flashes, and an exclamation mark (!) is displayed in the inventory display for the indicated slot number. Export the media to clear the state.
W
Wendy BakerSep 2, 2025
How to identify bad, defective, or contaminated media in Fujitsu ETERNUS LT60 S2?
- A
  Alicia WilsonSep 3, 2025
  If the Media Attention LED clears but immediately reappears each time a particular cartridge is reloaded after cleaning the drive, suspect that cartridge is defective. Export the cartridge and load a known good cartridge. In some cases, a cartridge can be worn out, have a defective Cartridge Memory, or have been formatted as a Firmware Upgrade Cartridge. Any cartridge suspected of being defective or contaminated should not be reused in any drive.
S
Sydney LamSep 6, 2025
How to prevent contamination by loose debris in Fujitsu Storage?
- L
  loganbenjaminSep 6, 2025
  To prevent contamination by loose debris in your Fujitsu Storage, ensure the library is installed in a clean, contamination-free environment. Store cartridges vertically in their plastic cases and continue cleaning the tape drive as needed.
A
Amber HarperSep 9, 2025
How long is a Fujitsu Storage cleaning cartridge good for?
- P
  princedavidSep 9, 2025
  A cleaning cartridge for Fujitsu Storage Ultrium universal libraries is good for 50 cleans.

Fujitsu ETERNUS LT60 S2 Specifications

General

Model	ETERNUS LT60 S2
Type	Tape Library
Tape Technology	LTO-6
Data Transfer Rate (Native, LTO-6)	160 MB/s
Data Transfer Rate (Compressed, LTO-6)	400 MB/s
Drive Types	LTO-6
Connectivity	SAS
Form Factor	Rack-mountable
Number of Drives	1 or 2
Supported Media	LTO Ultrium 6, LTO Ultrium 5
Power Supply	AC 100-240 V, 50/60 Hz
Operating Temperature	10 to 35 °C
Operating Humidity	20% to 80% (non-condensing)
Warranty	1 year
Number of Slots	60 slots
Dimensions (W x D x H)	447 mm x 740 mm x 177 mm