EasyManuals Logo

Fujitsu PRIMERGY RX2540 M1 Operating Manual

Fujitsu PRIMERGY RX2540 M1
92 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #44 background imageLoading...
Page #44 background image
44 Operating Manual
RX2540 M1
Important information
4.3 FCC Class A Compliance Statement
If there is an FCC statement on the device, it applies to the products covered in
this manual, unless otherwise specified herein. The statement for other
products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a
"Class A" digital device, pursuant to Part 15 of the FCC rules and meets all
requirements of the Canadian Interference-Causing Equipment Standard
ICES-003 for digital apparatus. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in strict accordance with the instructions, may cause harmful
interference to radio communications. However, there is no warranty that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Fujitsu is not responsible for any radio or television interference caused by
unauthorized modifications of this equipment or the substitution or attachment
of connecting cables and equipment other than those specified by Fujitsu. The
correction of interferences caused by such unauthorized modification,
substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to
any and all optional peripheral or host devices. Failure to do so may violate FCC
and ICES rules.
WARNING:
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Table of Contents

Other manuals for Fujitsu PRIMERGY RX2540 M1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY RX2540 M1 and is the answer not in the manual?

Fujitsu PRIMERGY RX2540 M1 Specifications

General IconGeneral
Tcase72.6 °C
Bus typeQPI
SteppingR2
FSB ParityNo
Scalability2S
Processor codeSR207
Processor cache15 MB
Processor cores6
Processor modelE5-2620V3
System bus rate8 GT/s
Processor seriesIntel Xeon E5-2600 v3
Processor socketLGA 2011-v3
Processor threads12
Processor codenameHaswell
Execute Disable BitYes
Motherboard chipsetIntel® C612
Processor frequency2.4 GHz
Processor cache typeSmart Cache
Processor lithography22 nm
Processor manufacturerIntel
Processor package size52.5 x 45 mm
Processor front side bus- MHz
Processor boost frequency3.2 GHz
Processor operating modes64-bit
PCI Express configurationsx4, x8, x16
Supported instruction setsAVX
Thermal Design Power (TDP)85 W
Compatible processor seriesIntel® Xeon®
Number of processors installed1
Maximum number of SMP processors2
Maximum number of PCI Express lanes40
Memory types supported by processorDDR4-SDRAM
Memory channels supported by processorQuad
Memory clock speeds supported by processor1600, 1866 MHz
Memory bandwidth supported by processor (max)59 GB/s
Maximum internal memory supported by processor768 GB
HDD size- \
RAID levels0, 1, 5, 6, 10, 50, 60
Optical drive typeDVD Super Multi
Supported HDD sizes3.5 \
Total storage capacity- GB
Maximum storage capacity- TB
Number of HDDs installed-
Number of HDDs supported4
Supported storage drive interfacesSAS, Serial ATA
Memory slots24
Internal memory8 GB
Memory clock speed2133 MHz
Maximum internal memory1536 GB
Memory layout (slots x size)1 x 8 GB
LAN controllerIntel I210
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
USB 2.0 ports quantity5
PCI Express slots version3.0
PCI Express x8 (Gen 3.x) slots3
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)10 - 85 %
CertificationCB, RoHS, WEEE, GS, CE, CSAc/us, FCC, VCCI, KC, CCC, C-Tick, CNS
Power supply450 W
Power supply input frequency47 - 63 Hz
Chassis typeRack (2U)
Operating system installedWindows Server 2012 R2 Datacenter
Compatible operating systemsWindows Hyper-V Server 2012 R2 Windows Server 2012 R2 Datacenter Windows Server 2012 R2 Standard Windows Storage Server 2012 R2 Standard Windows Hyper-V Server 2012 Windows Server 2012 Datacenter Windows Server 2012 Standard Windows Hyper-V Server 2008 R2 Windows Server 2008 R2 Datacenter Windows Server 2008 R2 Enterprise Windows Server 2008 R2 Standard VMware vSphere 5.5 VMware vSphere 5.1 Embedded VMware vSphere 5.1 SUSE Linux Enterprise Server 11 Red Hat Enterprise Linux 7 Red Hat Enterprise Linux 6 Oracle Linux 7 Oracle Linux 6 Oracle VM 3
Processor ARK ID83352
Intel Secure Key Technology version1.00
Intel Identity Protection Technology version0.00
On-board graphics card modelNot available
Weight and Dimensions IconWeight and Dimensions
Depth770 mm
Width482.6 mm
Height86.9 mm
Weight25000 g

Related product manuals