Technical Support is available 8am-5pm PST. Monday - Friday
support@fslaser.com • 702-802-3103
13
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Assembly Stage 2: Connect the Exhaust System
It is required that an exhaust fan is connected and operating whenever you run a job on your laser.
A properly installed exhaust fan removes smoke and fumes from the case and exhausts them to the
outside of the building or a fume extractor. For Coolbox users, skip this step and refer to Appendix A:
Coolbox Assembly.
1. Position Ducting: Place your 4” ducting over the Exhaust Port located at the back of the
machine and hold. Secure with 4” ducting clamp.
2. Attach Exhaust Fan: Secure the other end of the ducting, connected
to the machine, to the exhaust fan. Now repeat the ducting and clamping process on the other side
of the exhaust fan, creating a sequence of machine to ducting to exhaust fan to second ducting. Now
plug in the exhaust fan into the bottom power plug marked “exhaust” on the back of your Muse 3D
machine.
Figure 3.3
Figure 3.4
Figure 3.5
Additional
Accessory
Fan
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Assembly Stage 2: Connect the Exhaust System
It is required that an exhaust fan is connected and operating whenever you run a job on your laser.
A properly installed exhaust fan removes smoke and fumes from the case and exhausts them to the
outside of the building or a fume extractor. For Coolbox users, skip this step and refer to Appendix A:
Coolbox Assembly.
1. Position Ducting: Place your 4” ducting over the Exhaust Port located at the back of the
machine and hold. Secure with 4” ducting clamp.
2. Attach Exhaust Fan: Secure the other end of the ducting, connected
to the machine, to the exhaust fan. Now repeat the ducting and clamping process on the other side
of the exhaust fan, creating a sequence of machine to ducting to exhaust fan to second ducting. Now
plug in the exhaust fan into the bottom power plug marked “exhaust” on the back of your Muse 3D
machine.
Figure 3.3
Figure 3.4
Figure 3.5
Additional
Accessory
Fan
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Assembly Stage 2: Connect the Exhaust System
It is required that an exhaust fan is connected and operating whenever you run a job on your laser.
A properly installed exhaust fan removes smoke and fumes from the case and exhausts them to the
outside of the building or a fume extractor. For Coolbox users, skip this step and refer to Appendix A:
Coolbox Assembly.
1. Position Ducting: Place your 4” ducting over the Exhaust Port located at the back of the
machine and hold. Secure with 4” ducting clamp.
2. Attach Exhaust Fan: Secure the other end of the ducting, connected
to the machine, to the exhaust fan. Now repeat the ducting and clamping process on the other side
of the exhaust fan, creating a sequence of machine to ducting to exhaust fan to second ducting. Now
plug in the exhaust fan into the bottom power plug marked “exhaust” on the back of your Muse 3D
machine.
Figure 3.3
Figure 3.4
Figure 3.5
Additional
Accessory
Fan
Section III. Installation & Assembly
2. Connect the Exhaust System
Assembly Stage 2: Connect the Exhaust System
It is required that an exhaust fan is connected and operating whenever you run a job on your laser. A properly
installed exhaust fan removes smoke and fumes from the case and exhausts them to the outside of the
building or a fume extractor.
1.Position Ducting: Place your 4” ducting over the Exhaust Port located at the back of the machine and
hold. Secure with 4” ducting clamp.
2.Attach Exhaust Fan: Secure the other end of the ducting, connected to the machine, to the exhaust
fan. Now repeat the ducting and clamping process on the other side of the exhaust fan, creating a
sequence of machine to ducting to exhaust fan to second ducting. Now plug in the exhaust fan into the
bottom power plug marked “exhaust” on the back of your Muse 3D machine.
To Next Page
Loading...