FUTABA 12K - Page 138

138
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQQDPH
and return to the Model
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
<Push Dial>
RETURN
This function adjusts the throttle curve for
optimum engine speed from throttle stick input.
*When throttle curve is set to ON when there is no throttle
function; this curve acts as the motor function.
NOTE: If this throttle curve function is activated,
you can not use the THR-EXP function within
the DUAL RATE function simultaneously.
ŏ6HOHFW>7+5&859(@DWWKH0RGHOPHQX
and access the setup screen shown
below by pushing the RTN button.
ŏ&XUYHUDWH
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
THR CURVE
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGSXVK
the RTN button to switch to the data input
mode.
 6HOHFWWKH21PRGHE\VFUROOLQJWKH3XVK
dial.
*The display blinks.
 3XVKWKH571EXWWRQWRDFWLYDWHWKHIXQFWLRQ
and return to the cursor mode.
ƔSRLQWFXUYHVHWWLQJ
>&XUYHUDWHVHWWLQJ@
1. Move the cursor to the curve rate setting
LWHP\RXZDQWWRDGMXVWDQGSXVKWKH571
button to switch to the data input mode.
 $GMXVWWKHUDWHE\VFUROOLQJWKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>0RYLQJFXUYHSRLQW@
1. Move the cursor to the curve point setting
LWHP\RXZDQWWRDGMXVWDQGSXVKWKH571
button to switch to the data input mode.
 $GMXVWWKHFXUYHSRLQWE\VFUROOLQJ WKH3XVK
dial.
 ,QLWLDOYDOXH3333
3
 $GMXVWPHQWUDQJH8SWRLQIURQWRIWKH
DGMRLQLQJSRLQW
*When the RTN button is pushed for one second, the curve
position is reset to the initial value.)
 3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>'HOHWLQJUHWXUQLQJFXUYHSRLQW@
Move the cursor to the curve point setting
LWHP\RXZDQWWRGHOHWHUHWXUQDQGSXVKWKH
RTN button for one second.
ŏ&XUYHSRLQW