FUTABA 12K - Page 145

145
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQQDPH
and return to the Model
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
<Push Dial>
RETURN
RUDDER2
RUDDER
RUDDER
V-TAIL
RUDDER2
Winglet
RUDDER1
Winglet
atFlyingwing
atFlyingwing
()
()
AIL3
AIL3
(ChipAileron)
(ChipAileron)
AIL1
(MainAileron)
AIL2
(MainAileron)
AIL to RUD
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
Use this mix when you want to mix the rudders
with aileron operation. This allows the aircraft to
bank at a steep angle.
ŏ0L[LQJGXULQJIOLJKWFDQEHWXUQHG 212)) E\D
VZLWFK$OZD\V21DW>@VHWWLQJ
ŏ7KHPL[LQJUDWHFDQEHDGMXVWHG
ŏ6HOHFW>$,/WR58'@DWWKH0RGHO
menu and access the setup
screen shown below by pushing
the RTN button.
*The display screen is an example.
The actual screen depends on the
model type.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
(Glider: Currently selected condition name)
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGSXVK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
3XVKGLDO
*The display blinks.
 3XVKWKH571EXWWRQWRDFWLYDWHWKHIXQFWLRQ
DQGUHWXUQWRWKHFXUVRUPRGH21LV
GLVSOD\HG
When selecting a switch, move the cursor to
WKH>6:@LWHPDQGSXVKWKH571EXWWRQWRFDOO
WKHVHOHFWLRQVFUHHQ6HOHFW WKHVZLWFKDQG
VHWLWV21GLUHFWLRQ$OZD\V21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the left or right item
and push the RTN button to switch to the
GDWDLQSXWPRGH$GMXVWWKHPL[LQJUDWH
LQGHSHQGHQWO\E\VFUROOLQJWKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ)LQHWXQLQJ
Operation Mode
:KHQWKH¿QHWXQHFRQWUROLVVHWLWLV
displayed.
Mode : LIN. / ATL+ / ATL- / SYM.
Actual rate
It can be set by each conditions.
7KH¿QHWXQHFRQWURO
hardware
7KH¿QHWXQHUDWH
Range ： -100 〜 +100%