FUTABA 12K - Page 160

160
<Model Menu (Airplane/Glider Functions)>
When setting a rate selection switch, move
the cursor to the switch item and push the
RTN button to access the selection screen.
6HOHFWWKHVZLWFKDQGVHWLWV21GLUHFWLRQ
$OZD\V21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ*\URW\SHVHOHFWLRQ
Move the cursor to the gyro type selection
item and push the RTN button to switch to
WKHGDWDLQSXWPRGH6HOHFWWKHJ\URW\SH
E\VFUROOLQJWKH3XVKGLDO
 >*<@:KHQD)XWDED*<$J\URLVXVHG
 >1250@:KHQXVLQJVRPHWKLQJRWKHUWKDQ
)XWDED*<$J\URLVXVHG
 3XVKWKH571EXWWRQWRFKDQJHWKHJ\URW\SH
and return to the cursor mode.
*When a Futaba GYA gyro is used and [GY] type is selected,
the sensitivity set value is directly read in both the AVCS
and NORM modes.
Ɣ2SHUDWLRQPRGHVHOHFWLRQ*<$J\UR
Move the cursor to the operation mode
selection item and push the RTN button to
VZLWFKWRWKHGDWDLQSXWPRGH6HOHFWWKH
RSHUDWLRQPRGHE\VFUROOLQJWKH3XVKGLDO
 >$9&6@$9&6PRGH
 >1250@1RUPDOPRGH
 3XVKWKH571EXWWRQWRFKDQJHWKHRSHUDWLRQ
mode and return to the cursor mode.
Ɣ6HQVLWLYLW\VHWWLQJ
Move the cursor to the sensitivity icon and
push the RTN button to switch to the data
input mode.
 $GMXVWWKHVHQVLWLYLW\ E\VFUROOLQJWKH3XVK
dial.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the
sensitivity is reset to the initial value.)
 3XVKWKH571EXWWRQWRUHWXUQWRWKHFXUVRU
mode.
([DPSOH6HWWLQJWKUHHD[LVXVLQJD*<$DQG*<$
ŏ:LQJW\SH$LOHURQVHUYRVPRXQWHGIXVHODJHVHOHFWHG
ŏ6HW
5CH → GYRO
*<$$,/
7CH → GYRO2
*<$(/(
8CH → GYRO3
*<$58'
CTRL
andTRIM → [--]
DWWKH)XQFWLRQPHQXRIWKH/LQNDJHPHQX
ŏ*<52VHWWLQJRIWKH0RGHOPHQX
*Set so that Rate 1 is turned on at the back position of switch E and Rate 3 is turned ON at the front position. Since
switch E is turned OFF at the center, Rate 2 remains [INH].
Receiver
Rudderservo
Elevatorservo
GYA440
GYA441
GYA441
Aileronservo
S.BUS/S.BUS2port
GAIN0％
AVCS
NORMAL
WhenAVCSisusedwe
recommendthatthe
sensitivityCHbesetto
the3-position.
Rate GYRO GYRO ２ GYRO ３ TYPE ACT/INH SW
#1 AVCS:60% AVCS:60% AVCS:60% GY OFF/ON SE
#2 INH
#3 NORM:60% NORM:60% NORM:60% GY ON/OFF SE