FUTABA 12K - Page 159

159
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQQDPH
and return to the Model
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
<Push Dial>
RETURN
GYRO
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
This function is used when a GYA Series gyro
is used to stabilize the aircraft's attitude. The
sensitivity and operation mode (Normal mode/
AVCS mode) can be changed via a switch.
ŏ7KUHHUDWHV5DWH5DWH5DWHFDQEH
switched.
ŏ8SWRD[HV*\UR*\UR*\UR  FDQEH
simultaneously controlled.
Note: This setting does not assign a sensitivity
channel. To do so, use the Linkage menu
prior to assigning the sensitivity channel
(Gyro/Gyro2/Gyro3), be sure to select an
unused channel.
Set the [Control] and [Trim] settings other than
Function to [--].
ŏ7KHRSHUDWLRQPRGH$9&6
125DQGVHQVLWLYLW\RIWKH
WKUHHD[LV*\UR*\UR*\UR
can be set.
ŏ6HOHFW>*<52@DWWKH0RGHOPHQXDQG
access the setup screen shown below
by pushing the RTN button.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
(Active rate # display)
ŏ *\URW\SH
selection
ŏ $&7,1+
ŏ 6ZLWFKVHOHFWLRQ
ŏ5DWHVHWXS
screen selection
>5DWHVHWXSVFUHHQ@
>5DWHVHWXSVFUHHQ@
>5DWHVHWXSVFUHHQ@
Setting method
*Prior to using the Function menu in the Linkage menu to
assign the sensitivity channel (Gyro/Gyro2/Gyro3) select an
unused channel.
Set [Control] and [Trim] other than function to [--].
Ɣ5DWHVHWXSVFUHHQVHOHFWLRQ
Move the cursor to the setup screen selection
item and push the RTN button to switch
WRWKHGDWDLQSXWPRGH6HOHFWWKHVHWXS
VFUHHQE\VFUROOLQJWKH3XVKGLDO
 3XVKWKH571EXWWRQ WRFKDQJHWKHVHWXS
screen and return to the cursor mode.
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYH WKHFXUVRUWRWKH>,1+@LWHPDQGSXVK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
3XVKGLDO
*The display blinks.
 3XVKWKH571EXWWRQWRDFWLYDWHWKHIXQFWLRQ
and return to the cursor mode.
ŏ
7KHÀQHWXQLQJKDUGZDUH
setting
6HWWLQJUDQJH：
GY type :6HWWLQJUDWH7KH
actual rate has not to be
JUHDWHUWKDQ
NORM type : 6HWWLQJUDWH7KH
actual rate has not to be greater
WKDQ