FUTABA 12K - Page 158

158
<Model Menu (Airplane/Glider Functions)>
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGSXVK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
3XVKGLDO
*The display blinks.
 3XVKWKH571EXWWRQWRDFWLYDWHWKHIXQFWLRQ
DQGUHWXUQWRWKHFXUVRUPRGH21LV
GLVSOD\HG
When setting a switch, move the cursor to
the switch item and push the RTN button
WRDFFHVVWKHVHOHFWLRQ VFUHHQ6HOHFWWKH
VZLWFKDQGVHWLWV21GLUHFWLRQ$OZD\V21
DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ2IIVHWUDWHDGMXVWPHQW
 0RYHWKHFXUVRUWRWKHDLOHURQÁDSUXGGHURU
elevator rate item and push the RTN button
WRVZLWFKWRWKHGDWDLQSXWPRGH$GMXVWWKH
UDWHLQGHSHQGHQWO\E\VFUROOLQJWKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ6HUYRVSHHGVHWWLQJ
Move the cursor to the aileron, flap, rudder
or elevator speed item and push the RTN
button to switch to the data input mode.
 $GMXVWWKHUDWHE\VFUROOLQJWKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHaPD[LPXPGHOD\
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRUHWXUQWRWKHFXUVRU
mode.
Ɣ$XWRVZLWFKVHOHFWLRQ
When setting a auto switch, move the cursor
WRWKH>$8726:@LWHPDQGSXVKWKH571
EXWWRQWRDFFHVVWKHVHOHFWLRQVFUHHQ6HOHFW
WKHVZLWFKDQGVHWLWV21GLUHFWLRQ$OZD\V
21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
ThescreenofOffsetmode
The operation hardware is set.
The default setting is below;
Stick Mode 1 : J2
Stick Mode 2 : J3
Ɣ/LQHDUPRGH
,Q/LQHU0RGH$LUEUDNH LVRSHUDWHGE\WKH
stick or lever.
The start point of the mixing can be set.
Modebutton
OFS :
Offsetmode
LIN :
Linearmode
The start point this mixer is set.
< > is current position of MASTER.
At J1, J4, LD and RD, the left end
point is 0%, the right end point is
100%.
At J2, J3, LS, RS and SA~SH, the
upper end point is 100%, the lower
end point is 0%
Operatedbythe
stickorlever
Lowside Airbrakemoves
Airbrake
doesn'tmove.
Airbrakemovesin
linear
e.g.Startpoint
J3:
＜
50%
＞