FUTABA 12K - Page 169

169
<Model Menu (Airplane/Glider Functions)>
<Push Dial>
FLT. MODE
>&RUUHVSRQGLQJPRGHOW\SH@0XOWLURWRU
In the FLT. MODE (flight mode), you can
change the multicopter mode to up to 3 CH, 5
signals set with any switch. It is used in the case of
a multicopter controller of the type that can change
WKHÀLJKWPRGH
Setting method
Ɣ)XQFWLRQVHWWLQJ
 $VVLJQWKHFKDQQHOWREHXVHGZLWKWKH
IXQFWLRQRIWKHOLQNDJHPHQX02'(
02'(02'(
Ɣ5DWHDGMXVWPHQW
 0RYHWKHFXUVRUWRWKH)0)002'(
02'(LWHPIRUHDFKGLUHFWLRQDQGSXVKWKH
RTN button to switch to the data input mode.
$GMXVWWKHUDWHLQGHSHQGHQWO\E\VFUROOLQJ
WKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
ŏ6HOHFW>)/702'(@DWWKH0RGHOPHQX
and access the setup screen shown
below by pushing the RTN button.
ŏ6HOHFW>)81&7,21@DWWKH/LQNDJHPHQXDQGDFFHVVWKH
setup screen shown below by pushing the RTN button.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ6ZLWFKVHOHFWLRQ
● MODE
● MODE2
● MODE3
,QLWLDOYDOXH


$GMXVWPHQWUDQJH

〜

ŏ6HWWKHIOLJKWPRGH
selection switch. When
)0WR)0DUHDOO2))
)0LVVHOHFWHG
ŏ$VVLJQ02'(WRWKH
channel to be used for
ÁLJKWPRGHLQDGYDQFH
ŏ$&7,1+
ON during operation
3ULRULW\+LJK
3ULRULW\/RZ
<Model Menu (Multirotor Functions)>
ŏ,WLVSRVVLEOHWRVHWIXQFWLRQVRI02'(02'(
02'(
ŏ)LYHW\SHVRIIOLJKWPRGHVZLWFKLQJ VHWWLQJLV
possible for each function.
ŏ7KHVHWWLQJUDQJHLVDERXW
µ
6WR
DERXW
µ
6
ŏ7KHSULRULW\RIWKHÁLJKWPRGHLV
)0)0)0)0)0
ŏ,WZLOOQRWZRUNLIDQ\IXQFWLRQRI02'(02'(
02'(LVQRWVHW
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
Ɣ6ZLWFKVHOHFWLRQ
Move the cursor to the switch item and
push the RTN button to access the selection
VFUHHQ6HOHFWWKHVZLWFKDQGVHWLWV21
direction.
*For a description of the switch selection method, see the
description at the back of this manual.