FUTABA 12K - Helicopter Basic Setting Procedure

51
<Receiver and Servo Installation>
1. Model addition and selection
Initially, the T12K assigns the first model to
PRGHOLQWKHWUDQVPLWWHU7RDGGQHZPRGHOV
or to select a model already programmed, use the
0RGHO6HOHFWIXQFWLRQRIWKH/LQNDJH0HQX
This is convenient when selecting a model
DIWHUHQWHULQJWKHPRGHOVQDPHVLQDGYDQFH7KH
7.LVFDSDEOHRIVWRULQJXSWRPRGHOVLQWKH
WUDQVPLWWHUVLQWHUQDOPHPRU\$GGLWLRQDOPRGHOV
FDQDOVREHVWRUHGLQDQRSWLRQDOPLFUR6'FDUG
The currently selected model is displayed in
the middle of the screen. Before flying and before
changing any settings, always confirm the model
name.
When a new model is added, the Model Type select
screen and system mode setup screen automatically
appear. Change, or check that they match the swash
type and receiver type of the model used.
:KHQDQHZPRGHOLVDGGHG\RXZLOOQHHGWRUH
link the receiver.
2. Model type and swash type selection
If a different model type is already selected,
select helicopter with the Model Type function of
the Linkage Menu, and then select the swash type
matched to the helicopter.
*The Model Type function automatically selects the
Helicopter basic setting procedure
This section outlines examples of use of the helicopter functions of the T12K. Adjust the actual values,
etc. to match the fuselage used.
appropriate output channels, control functions, and mixing
IXQFWLRQVIRUWKHFKRVHQPRGHOW\SH6L[VZDVKW\SHVDUH
available for helicopters.
*For a description of the swash type selection, refer to the
02'(/7<3(IXQFWLRQ
3. Flight condition addition
7KHWUDQVPLWWHURIIHUVXSWR¿YHÀLJKWFRnditions
per model.
7KH&RQGLWLRQ6HOHFWIXQFWLRQDXWRPDWLFDOO\
DOORFDWHV¿YHFRQGLWLRQVIRUKHOLFRSWHUV
 ,QLWLDOVHWWLQJ
 ŏ1250$/
 ŏ,'/(836:(
 ŏ,'/(836:(
 ŏ,'/(836:)
 ŏ+2/'+ROGVZLWFKLVQRWDVVLJQHGLQLWLDOO\
Note: Since you may accidentally activate
a condition that not previously setup during
ÁLJKWZKLFKFRXOGFDXVHDFUDVKZHVXJJHVW
deleting conditions that are not used.
*For a description of the condition deletion, refer to the
&RQGLWLRQ6HOHFWIXQFWLRQ
The NORMAL condition is always on, and
remains on until other conditions are activated by
switches.
The priority is throttle hold/idle up 3/idle up 2/
idle up 1/normal. Throttle hold has the highest
priority.
7KH&RQGLWLRQ'HOD\FDQEHSURJUDPPHGIRU
HDFKFKDQQHODQGFRQGLWLRQ7KH&RQGLWLRQ'HOD\
is used to change the servo throw smoothly when
switching conditions.
*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOH
ŏ1RUPDO8VHLQLWLDOVHWWLQJFRQGLWLRQVRSHUDWH
ZKHQVZLWFK2))
8VHIURPHQJLQHVWDUWLQJWRKRYHULQJ
ŏ,GOHXS2SHUDWHDW6:(FHQWHU
8VHLQVWDOOWXUQORRSDQGRWKHUPDQHXYHUV
ŏ,GOHXS2SHUDWHDW6:(IRUZDUGVLGH
8VHLQUROOV
ŏ7KURWWOHKROG2SHUDWHDW6:*IRUZDUGVLGH
8VHLQDXWRURWDWLRQ